数据搜索系统,热门电子元器件搜索
  Chinese▼

Delete All
ON OFF
ALLDATASHEETCN.COM

X  

预览 PDF HTML

DMS3106B20-10SX Datasheet(数据表) 18 Page - DDK Ltd.

部件型号  DMS3106B20-10SX
说明  MIL-DTL-5015 Style Circular Connectors
下载  18 Pages
Scroll/Zoom Zoom In 100% Zoom Out
制造商  DDK [DDK Ltd.]
网页  http://www.ddknet.co.jp/English/index.html
标志 

DMS3106B20-10SX Datasheet(HTML) 18 Page - DDK Ltd.

 
Zoom Inzoom in Zoom Outzoom out
 18 page
background image
http://www.ddknet.co.jp
D/MS A/B Series
18
◎ Specifications and/or dimensions in this catalog are subject to change without notice.
 Your checking the latest specifications with our drawings would be highly appreciated.
○WIRING INSTRUCTION
Pre-solder the solder cups before you solder the wire.
Solder the wire quickly to prevent the flux and the solder from flowing out of the solder cups.
** How to remove the retaining ring
Insert the thin tip such like that of a screwdriver into the notch of the shell. Remove the retaining
ring carefully with it so as for the ring not to pop out while you put the finger on it lightly.
** How to install the retaining ring
Insert one end of the retaining ring into the groove of the shell. Then push the other end of
the retaining ring into the groove of the shell by the tip such like that of a screwdriver while you
compress the ring slightly.
Remove the retaining ring.
Fasten the retaining ring.
↑ Receptacle Shell
↑ Receptacle Shell
↑ Retaining Ring
** Soldering
〈How to wire connector〉
Regarding the connectors which have backshells, D/MS3100A, D/MS3101A, D/MS3106A,
D/MS3106B and D/MS3108B types, refer to diagram on the page 17. Remove the backshell and
the coupling ring. Thread the cable into the backshell and the cable clamp before soldering.
After the soldering, screw the dackshell frist and the cable clamp secondly. Be careful to tighten
the screws of the cable clamp not to press the soldering contacts .
When the cable is too thin to fasten tightly, duplicate or triplicate the rubber bushing, AN3420-□□.
〈Soldering thick contacts〉
Since #0, #4 and #8 sizes contacts take longer time to solder,the insert assembly which made of
resin may be damaged by high temperature.
To avoid this trouble, we recommend that the contacts be removed from the insert assembly and
solder each contacts. Firstly, remove the retaining ring and pull out the insert assembly from the
shell. Secondly, float the rear insert to pull out a contact with rotating it by hand.
On inserting the contacts, do it reverse order.
※ Caution
When you check the electrical continuity, use a mating half connector.
In case of mating other conductors such as a clip it causes the trouble surface finish, retaining
tension, and deteriorate.




HTML 页

1  2  3  4  5  6  7  8  9  10  11  12  13  14  15  16  17  18 


数据表 下载




链接网址


Privacy Policy
ALLDATASHEETCN.COM
ALLDATASHEET是否为您带来帮助?  [ DONATE ]  

关于 Alldatasheet    |   广告服务   |   联系我们   |   隐私政策   |   书签   |   链接交换   |   制造商名单
All Rights Reserved© Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  , Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp  |   Russian : Alldatasheetru.com
Korean : Alldatasheet.co.kr   |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com  |   Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl