数据搜索系统,热门电子元器件搜索 |
|
TS8388BCFS 数据表(PDF) 9 Page - ATMEL Corporation |
|
TS8388BCFS 数据表(HTML) 9 Page - ATMEL Corporation |
9 / 57 page 9 TS8388B 2144C–BDC–04/03 Notes: 1. Differential output buffers are internally loaded by 75 Ω resistors. Buffer bias current = 11 mA. 2. See “Definition of Terms” on page 48. 3. Histogram testing based on sampling of a 10 MHz sinewave at 50 MSPS. 4. Output error amplitude < ± 4 lsb around correct code (including gain and offset error). 5. Maximum jitter value obtained for single-ended clock input on the JTS8388B die (chip on board): 200 fs. (500 fs expected on TS8388BG) 6. Digital output back termination options depicted in Application Notes. 7. With a typical value of TD = 465 ps, at 1 GSPS, the timing safety margin for the data storing using the ECLinPS 10E452 out- put registers from Motorola® is of ± 315 ps, equally shared before and after the rising edge of the Data Ready signals (DR, DRB). 8. The clock inputs may be indifferently entered in differential or single-ended, using ECL levels or 4 dBm typical power level into the 50 Ω termination resistor of the inphase clock input. (4 dBm into 50Ω clock input correspond to 10 dBm power level for the clock generator.) 9. At 1 GSPS, 50/50 clock duty cycle, TC2 = 500 ps (TC1). TDR - TOD = -100 ps (typ) does not depend on the sampling rate. 10. Specified loading conditions for digital outputs: - 50 Ω or 75Ω controlled impedance traces properly 50/75Ω terminated, or unterminated 75Ω controlled impedance traces. - Controlled impedance traces far end loaded by 1 standard ECLinPS register from Motorola. (i.e.: 10E452) (Typical input parasitic capacitance of 1.5 pF including package and ESD protections.) 11. Termination load parasitic capacitance derating values: - 50 Ω or 75Ω controlled impedance traces properly 50/75Ω terminated: 60 ps/pF or 75 ps per additionnal ECLinPS load. - Unterminated (source terminated) 75 Ω controlled impedance lines: 100 ps/pF or 150 ps per additionnal ECLinPS termina- tion load. 12. Apply proper 50/75 Ω impedance traces propagation time derating values: 6 ps/mm (155 ps/inch) for TSEV8388B Evaluation Board. 13. Values for TOD and TDR track each other over temperature, (1% variation for TOD-TDR per 100 °C temperature variation). Therefore TOD-TDR variation over temperature is negligible. Moreover, the internal (on-chip) and package skews between each Data TODs and TDR effect can be considered as negligible. Consequently, minimum values for TOD and TDR are never more than 100 ps apart. The same is true for the TOD and TDR maximum values (see Advanced Application Notes about “TOD-TDR Variation Over Temperature” on page 27). 14. Min value guarantees performance. Max value guarantees functionality. 15. Min value guarantees functionality. Max value guarantees performance. Data ready output delay TDR 4 1110 1320 1620 ps (2)(10) (11)(12) Data ready reset delay TRDR 4 – 720 1000 ps Data to data ready – Clock low pulse width (See “Timing Diagrams” on page 10.) TOD-TDR 4 0 40 80 ps (9)(13) (14) Data to data ready output delay (50% duty cycle) at 1 GSPS (See “Timing Diagrams” on page 10.) TD1 4 420 460 500 ps (2)(15) Data pipeline delay TPD 4 4 clock cycles Table 3. Electrical Specifications (Continued) Parameter Symbol Test Level Value Unit Note Min Typ Max |
类似零件编号 - TS8388BCFS |
|
类似说明 - TS8388BCFS |
|
|
链接网址 |
隐私政策 |
ALLDATASHEETCN.COM |
ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |