数据搜索系统,热门电子元器件搜索 |
|
LM2720M 数据表(PDF) 5 Page - National Semiconductor (TI) |
|
|
LM2720M 数据表(HTML) 5 Page - National Semiconductor (TI) |
5 / 8 page Pin Description Pin Pin Name Pin Function 1 Vcc5V Supply Voltage Input (5V nominal) 2 Divsel Selects Phase Mode. Logic low selects 4 phase. Logic high selects 3 phase. 2 phase operation is achieved by using 2 outputs in 4 phase mode. 3 Clksel Clock Select: Logic high selects internal clock. Logic low selects external clock. 4 Extclk External Clock Input. Output frequency = Clock Input / No. of Phases. Connect to Vcc5V to select internal clock. 5 Rref Connects to external reference resistor. Sets the operating frequency of the internal clock and the ramp time for the PWM. Reference voltage at this pin is 1.26V. 6 Vid0 5-Bit DAC Input (LSB). 7 Vid1 5-Bit DAC Input. 8 Vid2 5-Bit DAC Input. 9 Vid3 5-Bit DAC Input. 10 Vid4 5-Bit DAC Input (MSB) 11 OC+ Over-current Comparator. Non-inverting input. 12 OC− Over-current Comparator. Inverting input. 13 COMP Compensation Pin. This is the output of the internal transconductance amplifier. Compensation network should be connected between this pin and feedback ground FBG. 14 FB Feedback Input. Normally Kelvin connected to supply output. 15 Bgout Current Limit Flag. Goes to logic low when current limit is activated. When over-current condition is removed, this pin is weakly pulled up to Vcc5V. 16 FBG Feedback Ground. This pin should be connected to the ground at the supply output. 17 ENABLE Output Enable Pin. Tie to logic high to enable and logic low to disable. 18 GND Power Ground Pin. 19 DRV2 Phase 2 Output. 20 DRV0 Phase 0 Output. 21 Vcc12V Supply Voltage for FET Drivers DRV0:3. 22 DRV1 Phase 1 Output. 23 DRV3 Phase 3 Output. 24 PWRGD Power Good. This is an open-drain output that goes low (low impedance to ground) when the output voltage travels out of the threshold window, and resume to open-drain state when V OUT recovers into the 50mV hysteresis window. The power good window threshold, i.e. ±100mV for 1.3V ≤ V OUT ≤ 1.9V or ±150mV for 2V ≤ VOUT ≤ 3.5V, is automatically set according to VID code. Connect a 1nF capacitor to ground to filter out the switching noise coupling from DRV3 to this pin. www.national.com 5 |
类似零件编号 - LM2720M |
|
类似说明 - LM2720M |
|
|
链接网址 |
隐私政策 |
ALLDATASHEETCN.COM |
ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |