Datasheet

www.rohm.com

TSZ02201-0RAR0G200100-1-2

© 2012 ROHM Co., Ltd. All rights reserved.

4/36

11.Jul.2014 Rev.004

TSZ22111･15･001

BA3472xxx

BA3472RFVM

BA3474xxx

BA3474RFV

Absolute Maximum Ratings (Ta=25℃)

Parameter

Symbol

Ratings

Unit

BA3472

BA3474

BA3472R

BA3474R

Supply Voltage

VCC-VEE

+36

V

Power Dissipation

Pd

SOP8

780

*1*13

-

-

-

mW

SSOP-B8

690

*2*13

-

-

-

MSOP8

590

*3*13

-

590

*3*13

-

-

-

625

*4*14

-

-

-

713

*5*15

-

-

-

937

*6*16

-

SOP-J8

675

*7*13

-

-

-

TSSOP-B8

625

*4*13

-

-

-

SOP14

-

610

*8*13

-

-

SSOP-B14

-

870

*9*13

-

870

*9*13

-

-

-

1187

*10*15

-

-

-

1689

*11*16

TSSOP-B14

-

850

*12*13

-

-

Differential Input Voltage

*17

Vid

+36

V

Input Common-mode

Voltage Range

Vicm

(VEE - 0.3) to VEE + 36

V

Input Current

*18

-10

mA

Operable with Low Voltage

Vopr

+3.0V to +36.0V

(±1.5V to ±18.0V)

V

Operating Temperature Range

Topr

-40 to +85(SOP14:to +75)

-40 to +105

℃

Storage Temperature Range

Tstg

-55 to +150

℃

Maximum Junction Temperature

Tjmax

+150

℃

*1

To use at temperature above Ta＝25℃ reduce 6.2mW/℃.

*2

To use at temperature above Ta＝25℃ reduce 5.5mW/℃

*3

To use at temperature above Ta＝25℃ reduce 4.8mW/℃

*4

To use at temperature above Ta＝25℃ reduce 5.0mW/℃

*5

To use at temperature above Ta＝25℃ reduce 5.7mW/℃

*6

To use at temperature above Ta＝25℃ reduce 7.5mW/℃

*7

To use at temperature above Ta＝25℃ reduce 5.4mW/℃

*8

To use at temperature above Ta＝25℃ reduce 4.9mW/℃

*9

To use at temperature above Ta＝25℃ reduce 7.0mW/℃

*10

To use at temperature above Ta＝25℃ reduce 9.5mW/℃

*11

To use at temperature above Ta＝25℃ reduce 13.5mW/℃

*12

To use at temperature above Ta＝25℃ reduce 6.8mW/℃

*13

Mounted on a FR4 glass epoxy PCB(70mm×70mm×1.6mm).

*14

Mounted on a FR4 glass epoxy 2 layers PCB 70mm×70mm×1.6mm (occupied copper area：15mm×15mm).

*15

Mounted on a FR4 glass epoxy 2 layers PCB 70mm×70mm×1.6mm (occupied copper area：70mm×70mm).

*16

Mounted on a FR4 glass epoxy 4 layers PCB 70mm×70mm×1.6mm (occupied copper area：70mm×70mm).

*17

The voltage difference between inverting input and non-inverting input is the differential input voltage.

Then input terminal voltage is set to more than VEE.

*18

An excessive input current will flow when input voltages of less than VEE-0.6V are applied.

The input current can be set to less than the rated current by adding a limiting resistor.

Caution: Operating the IC over the absolute maximum ratings may damage the IC. The damage can either be a short circuit between pins or an open circuit

between pins and the internal circuitry. Therefore, it is important to consider circuit protection measures, such as adding a fuse, in case the IC is

operated over the absolute maximum ratings.