数据搜索系统,热门电子元器件搜索 |
|
TDA2HVBRQABCQ1 数据表(PDF) 10 Page - Texas Instruments |
|
|
TDA2HVBRQABCQ1 数据表(HTML) 10 Page - Texas Instruments |
10 / 426 page 10 TDA2SX, TDA2SG TDA2HG, TDA2HV, TDA2LF SPRS951A – DECEMBER 2015 – REVISED APRIL 2016 www.ti.com Submit Documentation Feedback Product Folder Links: TDA2SX TDA2SG TDA2HG TDA2HV TDA2LF Terminal Configuration and Functions Copyright © 2015–2016, Texas Instruments Incorporated Table 4-1. Unused Balls Specific Connection Requirements (continued) Balls Connection Requirements AF14 / D21 / E20 / E23 / C20 / C21 / V28 / F18 These balls must be connect to the corresponding power supply through an external pull resistor if unused AB17 These balls must be connected to F22 (porz) if unused NOTE All other unused signal balls with a Pad Configuration Register can be left unconnected with their internal pullup or pulldown resistor enabled. NOTE All other unused signal balls without Pad Configuration Register can be left unconnected. 4.2 Ball Characteristics Table 4-2 describes the terminal characteristics and the signals multiplexed on each ball. The following list describes the table column headers: 1. BALL NUMBER: Ball number(s) on the bottom side associated with each signal on the bottom. 2. BALL NAME: Mechanical name from package device (name is taken from muxmode 0). 3. SIGNAL NAME: Names of signals multiplexed on each ball (also notice that the name of the ball is the signal name in muxmode 0). NOTE Table 4-2 does not take into account the subsystem multiplexing signals. Subsystem multiplexing signals are described in Section 4.4, Signal Descriptions. NOTE In the Driver off mode, the buffer is configured in high-impedance. 4. Hxx/LFx: This column shows if the functionality is applicable for TDA2Hxx / TDA2LFx devices. Note that the ball characteristics table presents the functionality of TDA2Sxx device. Hxx - TDA2HGx; TDA2HVx; LFx - TDA2LFx 5. MUXMODE: Multiplexing mode number: (a) MUXMODE 0 is the primary mode; this means that when MUXMODE=0, the function mapped on the pin corresponds to the name of the pin. The primary muxmode is not necessarily the default muxmode. NOTE The default muxmode is the mode at the release of the reset; also see the RESET REL. MUXMODE column. (b) MUXMODE 1 through 15 are possible muxmodes for alternate functions. On each pin, some muxmodes are effectively used for alternate functions, while some muxmodes are not used. Only MUXMODE values which correspond to defined functions should be used. 6. TYPE: Signal type and direction: – I = Input – O = Output – IO = Input or Output |
类似零件编号 - TDA2HVBRQABCQ1 |
|
类似说明 - TDA2HVBRQABCQ1 |
|
|
链接网址 |
隐私政策 |
ALLDATASHEETCN.COM |
ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |