数据搜索系统,热门电子元器件搜索 |
|
TPS40000 数据表(PDF) 6 Page - Texas Instruments |
|
|
TPS40000 数据表(HTML) 6 Page - Texas Instruments |
6 / 20 page TPS40000, TPS40001 TPS40002, TPS40003 TPS40004, TPS40005 SLUS507C − JANUARY 2002 − REVISED JUNE 2004 6 www.ti.com Terminal Functions TERMINAL I/O DESCRIPTION NAME NO. I/O DESCRIPTION BOOT 10 O Provides a bootstrapped supply for the topside MOSFET driver, enabling the gate of the topside MOSFET to be driven above the input supply rail COMP 3 O Output of the error amplifier FB 2 I Inverting input of the error amplifier. In normal operation the voltage at this pin is the internal reference level of 700 mV. GND 5 − Power supply return for the device. The power stage ground return on the board requires a separate path from other sensitive signal ground returns. HDRV 9 O This is the gate drive output for the topside N-channel MOSFET. HDRV is bootstrapped to near 2 ×VDD for good en- hancement of the topside MOSFET. ILIM 1 I A resistor is connected between this pin and VDD to set up the over current threshold voltage. A 15- µA current sink at the pin establishes a voltage drop across the external resistor that represents the drain-to-source voltage across the top side N-channel MOSFET during an over current condition. The ILIM over current comparator is blanked for the first 100 ns to allow full enhancement of the top MOSFET. Set the ILIM voltage level such that it is within 800 mV of VDD; that is, (VDD − 0.8) ≤ IILIM ≤ VDD. LDRV 6 O Gate drive output for the low-side synchronous rectifier N-channel MOSFET SS/SD 4 I Soft-start and overcurrent fault shutdown times are set by charging and discharging a capacitor connected to this pin. A closed loop soft-start occurs when the internal 3- µA current source charges the external capacitor from 0.17 V to 0.70 V. During the soft-start period, the current sink capability of the TPS40001 and TPS40003 is disabled. When the SS/SD voltage is less than 0.12 V, the device is shutdown and the HDRV and LDRV are driven low. In normal opera- tion, the capacitor is charged to 1.5 V. When a fault condition is asserted, the HDRV is driven low, and the LDRV is driven high. The soft-start capacitor goes through six charge/discharge cycles, restarting the converter on the seventh cycle. SW 8 O Connect to the switched node on the converter. This pin is used for overcurrent sensing in the topside N-channel MOSFET, zero current sensing in synchronous rectifier N-channel MOSFET, and level sensing for predictive delay circuit. Overcurrent is determined, when the topside N-channel MOSFET is on, by comparing the voltage on SW with respect to VDD and the voltage on the ILIM with respect to VDD. Zero current is sensed, when the rectifier N-channel MOSFET is on, by measuring the voltage on SW with respect to ground. Zero current sensing applies to the TPS40000/2 devices only. VDD 7 I Power input for the chip, 5.5-V maximum. Decouple close to the pin with a low-ESR capacitor, 1- µF or larger. |
类似零件编号 - TPS40000 |
|
类似说明 - TPS40000 |
|
|
链接网址 |
隐私政策 |
ALLDATASHEETCN.COM |
ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |