数据搜索系统,热门电子元器件搜索
  Chinese▼

Delete All
ON OFF
ALLDATASHEETCN.COM

X  

预览 PDF Download HTML

CZRA3011 Datasheet(数据表) 5 Page - Comchip Technology

部件型号  CZRA3011
说明  Surface Mount Zener Diode
下载  5 Pages
Scroll/Zoom Zoom In 100% Zoom Out
制造商  COMCHIP [Comchip Technology]
网页  http://www.comchiptech.com
标志 

CZRA3011 Datasheet(HTML) 5 Page - Comchip Technology

   
Zoom Inzoom in Zoom Outzoom out
 5 page
background image
APPLICATION NOTE:
Since the actual voltage available from a given zener
diode is temperature dependent, it is necessary to
determine junction temperature under any set of
operating conditions in order to calculate its value. The
following procedure is recommended:
Lead Temperature, TL, should be determined from:
TL = θLAPD + TA
θLA is the lead-to-ambient thermal resistance (°C/W)
and PD is the power dissipation. The value for θLA will
vary and depends on the device mounting method.
θLA is generally 30-40 °C/W for the various chips and
tie points in common use and for printed circuit board
wiring.
The temperature of the lead can also be measured using
a thermocouple placed on the lead as close as possible to
the tie point. The thermal mass connected to the tie point
is normally large enough so that it will not significantly
respond to heat surges generated in the diode as a result
of pulsed operation once steady-state conditions are
achieved. Using the measured value of TL, the junction
temperature may be determined by:
TJ = TL + ∆TJL
∆TJL is the increase in junction temperature above the
lead temperature and may be found from Figure 2 for a
train of power pulses or from Figure 10 for dc power.
∆TJL = θLAPD
For worst-case design, using expected limits of Iz, limits
of PD and the extremes of TJ (∆TJL ) may be estimated.
Changes in voltage, Vz, can then be found from:
∆V = θVZ ∆TJ
θVZ , the zener voltage temperature coefficient, is
found from Figures 5 and 6.
Under high power-pulse operation, the zener voltage
will vary with time and may also be affected significantly
be the zener resistance. For best regulation, keep current
excursions as low as possible.
Data of Figure 2 should not be used to compute surge
capability. Surge limitations are given in Figure 3. They
are lower than would be expected by considering only
junction temperature, as current crowding effects cause
temperatures to be extremely high in small spots resulting
in device degradation should the limits of Figure 3 be
exceeded.
www.comchip.com.tw
COMCHIP
COMCHIP
MDS0211015A
Page 5
Surface Mount Zener Diode
Surface Mount Zener Diode




HTML 页

1  2  3  4  5 


数据表 下载




链接网址


Privacy Policy
ALLDATASHEETCN.COM
ALLDATASHEET是否为您带来帮助?  [ DONATE ]  

关于 Alldatasheet    |   广告服务   |   联系我们   |   隐私政策   |   书签   |   链接交换   |   制造商名单
All Rights Reserved© Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  , Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp  |   Russian : Alldatasheetru.com
Korean : Alldatasheet.co.kr   |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com  |   Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl