数据搜索系统,热门电子元器件搜索 |
|
LD24-20-700W(A) 数据表(PDF) 4 Page - MicroPower Direct, LLC |
|
LD24-20-700W(A) 数据表(HTML) 4 Page - MicroPower Direct, LLC |
4 / 4 page MicroPower Direct We Power Your Success - For Less! 292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: sales@micropowerdirect.com www.micropowerdirect.com Notes: • All dimensions are typical in inches (mm) • Tolerance x.xx = ±0.02 (±0.50) • Pin 1 is marked by a “dot” or indentation on the top of the unit Pin Connections Pin Color LD24-xx-xxxW Pin Color LD24-xx-xxxWA 1 Black -VIN -DC Supply 1 Black -VIN -DC Supply 2 White No Wire 2 White VADJ PWM, On/Off 8 Blue -LED LED Cathode Conn. 8 Blue -LED LED Cathode Conn. 9 Yellow +LED LED Anode Conn. 9 Yellow +LED LED Anode Conn. 16 Red +VIN +DC Supply 16 Red +VIN +DC Supply Mechanical Dimensions Analog Output Current Control The output current of the unit can also be set by adjusting the voltage level on the VADJ input to a value between 0.3V to 1.25V (IOUT will vary from 25% to 100% of rated output current). Care must be taken not to exceed 1.25V on this input, or the driver may be damaged. A simple analog circuit using two low cost, switching regulators is shown at left. Work- ing from inputs that can range from 15 to 32 VDC,the top regulator (SR1) keeps the input to the LED driver at 12 VDC. The other regulator (SR2), driven off the same input line maintains the control voltage (for the VADJ input) at 5 VDC. The resister network of R1 and R2 can now be used to set the output cur- rent level of the LED driver. This level is equal to: V RR R XV 12 2 ADJ CTRL = + In the second circuit, the 5 VDC regulator (SR2) is replaced by the shunt regulator (D1) circuit con- nected in parallel with the resistor network. The regulator will maintain the voltage across R2 and R3 at 2.5 VDC, insuring that the 1.25 VDC limit on the VADJ pin will not be exceeded. This circuit will work for inputs between 7VDC and 30 VDC. When using the analog control input, the nominal output current is equal to: . II x V 125 NOM MAX ADJ = The VADJ input should be left open if not used. Grounding VADJ will shut the unit down. Connect- ing VADJ to directly to +VIN may damage the unit. Analog Output Current Control (7 - 30 VDC IN) |
类似零件编号 - LD24-20-700W(A) |
|
类似说明 - LD24-20-700W(A) |
|
|
链接网址 |
隐私政策 |
ALLDATASHEETCN.COM |
ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |