SI4740 datasheet(21/68 Pages) SILABS

部件名	SI4740

功能描述	Si470X/1X/2X/3X/4X EVALUATION BOARD TEST PROCEDURE

Download	68 Pages

Scroll/Zoom	100%

制造商	SILABS [Silicon Laboratories]

网页	http://www.silabs.com

标志

21 / 68 page

AN388

Rev. 0.2

21

2.3.9. Adjacent / Alternate Channel Selectivity

Selectivity is a measure of the performance of a radio receiver to respond only to the tuned transmission (such as

a radio station) and reject other signals nearby, such as another broadcast on an adjacent channel. Selectivity is

usually measured as a ratio in decibels, comparing the signal strength received against that of a similar signal on

another frequency. Selectivity measures the ratio of the unwanted to wanted RF input levels at which the audio-

frequency, signal-to-interference ratio (S/I ratio) is 30 dB. The audio output produced by the wanted RF signal is

the reference level (VAUDIO0). First the audio reference level is measured at high RF input level. Second, the

wanted RF level is un-modulated and the unwanted RF level is adjusted until the S/I ratio is 30 dB.

1. Connect test equipment as shown in Figures 1, 2, or 3.

2. Configure the tuner in standard configuration.

3. Configure the audio analyzer:

a. Select Analyze.

b. Set Function = RMS Select.

i.

Set Bandwidth = BP 3%.

ii. Set Units = dBV.

iii. Set Frequency Mode = FIX: 1 kHz.

4. Configure generator #1:

a. Set carrier frequency = 98.1 MHz.

b. Set RF level VRF0 =40 dBµV.

c. Select FM Modulation.

i.

Set FM Deviation = 22.5 kHz.

ii. Set source = LFGEN.

iii. Set LFGEN frequency = 1 kHz.

d. Enable modulation.

e. Enable carrier.

5. Record the audio level, VAUDIO0.

6. Disable generator #1 modulation.

7. Configure generator #2:

a. Set carrier frequency = 97.9 MHz (adjacent channel) or

b. Set carrier frequency = 97.7 MHz (alternate channel).

c. Set RF level = 60 dBµV.

d. Select FM Modulation.

i.

Set FM Deviation = 22.5 kHz.

ii. Set source = LFGEN.

iii. Set LFGEN frequency = 1 kHz.

e. Enable modulation.

f. Enable carrier.

8. Adjust generator #2 RF level*, VRF1, until the audio level, VAUDIO1 = VAUDIO0 –30dB.

9. Selectivity (dB) = VRF1 –VRF0.

*Note: Generator #1 RF level is set to 40 dBµV to be able to get selectivity results greater than 60 dB. This is not a limitation of

the FM tuner or the evaluation board. Maximum RF level setting for the R&S SML01 signal generator is 120 dBµV. You

cannot increase the RF level beyond this value, so if VRF0 = 60 dBµV, selectivity numbers would be limited to 60 dB.

类似零件编号 - SI4740

制造商	部件名	数据表	功能描述
Silicon Laboratories	SI4740	66Kb / 2P	Automotive AM/FM Radio Receiver
	SI4740	3Mb / 302P	Si47XX PROGRAMMING GUIDE
	SI4740	1Mb / 20P	Si474X ANTENNA, SCHEMATIC, LAYOUT, AND DESIGN GUIDELINES
	Si4740	9Mb / 164P	Thank you for purchasing the Silicon Laboratories

More results

类似说明 - SI4740

制造商	部件名	数据表	功能描述
Silicon Laboratories	AN651	1,014Kb / 60P	EVALUATION BOARD TEST PROCEDURE
Silicon Laboratories	AN646	1Mb / 46P	Si477X EVALUATION BOARD TEST PROCEDURE
NXP Semiconductors	ES-LPC435X	70Kb / 11P	Errata sheet LPC435x/3x/2x/1x Rev. 2-20 October 2012
ON Semiconductor	NCP1521BEVB	148Kb / 1P	Test Procedure for the NCP1521B Evaluation Board 5/31/2007
Sanyo Semicon Device	LV8804FVGEVB	147Kb / 4P	Test Procedure for the LV8804FVGEVB Evaluation Board 3/26/2012
Pulse A Technitrol Comp...	RAZ32011DM	1Mb / 19P	GNSS/2x LTE/0, 1x, 2x or 3x WiFiDirect Mount
	RAZ32011AM	2Mb / 19P	GNSS / 2x LTE / 0, 1x, 2x or 3x WiFi Adhesive Mount
	RAZ32011MM	2Mb / 19P	GNSS / 2x LTE / 0, 1x, 2x or 3x WiFi Magnetic Mount
JDS Uniphase Corporatio...	JSH-42L3AD3-5	941Kb / 45P	LW 4x/2x/1x FC SFP with DDM
Monolithic Power System...	EV3021DQ-00A	198Kb / 5P	1x, 1.5x, 2x Auto-Adjust Charge Pump White LED Backlight Evaluation Board