数据搜索系统,热门电子元器件搜索 |
|
LM2694MTX 数据表(PDF) 10 Page - Texas Instruments |
|
LM2694MTX 数据表(HTML) 10 Page - Texas Instruments |
10 / 26 page 0.62A Load Current Increases IPK IOCL IO 'I Normal Operation Current Limited STOP RUN RON/SD Input Voltage LM2694 VIN RON LM2694 SNVS444A – MAY 2006 – REVISED APRIL 2013 www.ti.com Figure 11. Shutdown Implementation Current Limit Current limit detection occurs during the off-time by monitoring the recirculating current through the free-wheeling diode (D1). Referring to Typical Application Circuit and Block Diagram, when the buck switch is turned off the inductor current flows through the load, into SGND, through the sense resistor, out of ISEN and through D1. If that current exceeds 0.62A the current limit comparator output switches to delay the start of the next on-time period if the voltage at FB is below 2.5V. The next on-time starts when the current out of ISEN is below 0.62A and the voltage at FB is below 2.5V. If the overload condition persists causing the inductor current to exceed 0.62A during each on-time, that is detected at the beginning of each off-time. The operating frequency is lower due to longer-than-normal off-times. Figure 12 illustrates the inductor current waveform. During normal operation the load current is Io, the average of the ripple waveform. When the load resistance decreases the current ratchets up until the lower peak reaches 0.62A. During the Current Limited portion of Figure 12, the current ramps down to 0.62A during each off-time, initiating the next on-time (assuming the voltage at FB is <2.5V). During each on-time the current ramps up an amount equal to: ΔI = (VIN - VOUT) x tON / L1 (8) During this time the LM2694 is in a constant current mode, with an average load current (IOCL) equal to 0.62A + ΔI/2. Figure 12. Inductor Current - Current Limit Operation N - Channel Buck Switch and Driver The LM2694 integrates an N-Channel buck switch and associated floating high voltage gate driver. The peak current allowed through the buck switch is 1.5A, and the maximum allowed average current is 1A. The gate driver circuit works in conjunction with an external bootstrap capacitor and an internal high voltage diode. A 0.022 µF capacitor (C4) connected between BST and SW provides the voltage to the driver during the on-time. During each off-time, the SW pin is at approximately -1V, and C4 charges from VCC through the internal diode. The minimum off-time of 265 ns ensures a minimum time each cycle to recharge the bootstrap capacitor. 10 Submit Documentation Feedback Copyright © 2006–2013, Texas Instruments Incorporated Product Folder Links: LM2694 |
类似零件编号 - LM2694MTX |
|
类似说明 - LM2694MTX |
|
|
链接网址 |
隐私政策 |
ALLDATASHEETCN.COM |
ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |