数据搜索系统,热门电子元器件搜索 |
|
ISL6119EVAL1 数据表(PDF) 1 Page - Intersil Corporation |
|
ISL6119EVAL1 数据表(HTML) 1 Page - Intersil Corporation |
1 / 13 page 1 ® FN9002.3 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright © Intersil Americas Inc. 2004. All Rights Reserved All other trademarks mentioned are the property of their respective owners. ISL6119 USB Dual Port Power Supply Controller The ISL6119 is a USB dual port power controller, fully independent overcurrent (OC) fault protection IC. Operational over the +2.5V to +5.5V range, this device features internal current monitoring, accurate current limiting, integrated power switches and current limited delay to latch-off for system protection. The ISL6119 current sense and limiting circuitry sets the current limit to a nominal 1A, making this device well suited for the USB port power management application. The ISL6119 provides OC fault notification, accurate current limiting and a consistent timed latch-off thus isolating and protecting the voltage bus in the presence of an OC event or short circuit. The 12ms time to latch-off is independent of the adjoining switch’s electrical or thermal condition and the OC response time is inversely related to the OC magnitude. Each ISL6119 incorporates in a single 8 lead SOIC package two 80m Ω N-channel MOSFET power switches for power control. Each switch is driven by a constant current source giving a controlled ramp up of the output voltage. This provides a soft start turn-on eliminating bus voltage drooping caused by inrush current while charging heavy load capacitances. Independent enabling inputs and fault reporting outputs for each channel are compatible with 3V and 5V logic to allow external control and monitoring. The ISL6119 undervoltage lockout feature prevents turn-on of the outputs unless the correct ENABLE state and VIN > 2.5V are present. During initial turn-on the ISL6119 prevents fault reporting by blanking the fault signal. Rising and falling outputs are current limited voltage ramps so that both the inrush current and voltage slew rate are limited, independent of load. This reduces supply droop due to surge and eliminates the need for external EMI filters. During operation, once an OC condition is detected the appropriate output is current limited for 12ms to allow transient conditions to pass. If still in current limit after the current limit period has elapsed, the output is then latched off and the fault is reported by pulling the corresponding FAULT low. The FAULT signal is latched low until reset by the ENABLE signal being de-asserted at which time the FAULT signal will clear. Features •80m Ω Integrated Power N-channel MOSFET Switches • Accurate Current Sensing and 1A Current Limiting • 12ms Fault Delay to Latch-Off, No Thermal Dependency • 2.5V to 5.5V Operating Range • Disabled Output Internally Pulled Low • Undervoltage Lockout • Controlled Turn-on Ramp Time • Channel Independent Fault Output Signals • Compatible with 3.3V and 5V Logic Families • Channel Independent Logic Level Enable High Inputs (ISL6119H) or Enable Low Inputs (ISL6119L) • Pb-Free Package Options • Available in Tape & Reel with ‘-T’ Part Number Suffix Applications • USB Port Power Management • Electronic Circuit Limiting and Breaker Pinout ISL6119 (SOIC) TOP VIEW Ordering Information PART NUMBER TEMP. RANGE (°C) PACKAGE PKG. DWG. # ISL6119LIB -40 to 85 8 Lead SOIC M8.15 ISL6119LIBZA (Note) -40 to 85 8 Lead SOIC (Pb-free) M8.15 ISL6119HIB -40 to 85 8 Lead SOIC M8.15 ISL6119HIBZA (Note) -40 to 85 8 Lead SOIC (Pb-free) M8.15 ISL6119EVAL1 Evaluation Platform ISL6119USBEVAL1 USB Dual Port Evaluation Platform NOTE: Intersil Pb-free products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate termination finish, which is compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J Std-020B. 1 2 3 4 8 7 6 5 VIN OUT_1 OUT_2 FAULT_1 FAULT_2 GND ENABLE_1 ENABLE_2 Data Sheet March 2004 |
类似零件编号 - ISL6119EVAL1 |
|
类似说明 - ISL6119EVAL1 |
|
|
链接网址 |
隐私政策 |
ALLDATASHEETCN.COM |
ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |