数据搜索系统,热门电子元器件搜索 |
|
LF9501 数据表(PDF) 2 Page - LOGIC Devices Incorporated |
|
LF9501 数据表(HTML) 2 Page - LOGIC Devices Incorporated |
2 / 7 page DEVICES INCORPORATED LF9501 Programmable Line Buffer 2 08/16/2000–LDS.9501-H Video Imaging Products Outputs DO9-0 — Data Output The 10-bit data output appears on DO9-0 on the Nth clock cycle, where N is the overall delay (desired delay). Controls LCEN — Length Control Enable When LCEN is driven LOW, the next active clock edge will cause the loading of the delay value present at the LC10-0 input. OE — Output Enable The Output Enable controls the state of DO9-0. Driving OE LOW enables the output port. When OE is HIGH, DO9-0 is placed in a high-impedance state. The internal transfer of data is not affected by this control. MODSEL — Mode Select The Mode Select pin is used to choose the desired mode of operation: data delay mode or data recirculation mode. Driving MODSEL LOW places the device in the delay mode. The device operates as a programmable pipeline register. New data from the DI9-0 input is loaded on every active edge of CLK. Driving MODSEL HIGH places the device in the data recirculation mode. The device operates as a programmable circular buffer. The output of the device is routed back to the input. MODSEL may be changed during device operation (synchronously), however, the required setup and hold times, with respect to CLK, must be met. SIGNAL DEFINITIONS Power VCC and GND +5 V power supply. All pins must be connected. Clock CLK — Master Clock The active edge of CLK, selected by CLKSEL, strobes all registers. All timing specifications are referenced to the active edge of CLK. Inputs DI9-0 — Data Input 10-bit data, from the data input, is latched into the device on the active edge of CLK when MODSEL is LOW. LC10-0 — Length Control Input The 11-bit value is used to specify the length of the delay buffer, between DI9-0 and DO9-0, or the amount of recirculation delay. An integer value ranging from 0 to 1279 is used to select a delay ranging from 2 to 1281 clock cycles. The value placed on the LC10-0 inputs is equal to the desired delay minus 2. The data presented on LC10-0 is loaded into the device on the active edge of CLK, selected by CLKSEL, in conjunction with LCEN being driven LOW. CLKSEL — Clock Select The CLKSEL control allows the selection of the active edge of CLK. A LOW on CLKSEL selects negative- edge triggering of the device. Driving CLKSEL HIGH selects positive-edge triggering. All timing specifications are referrenced to the selected active edge of CLK. CLKEN — Clock Enable The Clock Enable control enables and disables the CLK input. Driving CLKEN LOW enables CLK and causes the device to operate in a normal fashion. When CLKEN is HIGH, CLK is disabled and the device will hold all internal operations and data. CLKEN may be changed during device operation (synchronously), however, the required setup and hold times, with respect to CLK, must be met. The changing of CLKEN takes effect on the active edge of CLK following the edge in which it was latched. |
类似零件编号 - LF9501 |
|
类似说明 - LF9501 |
|
|
链接网址 |
隐私政策 |
ALLDATASHEETCN.COM |
ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |