数据搜索系统,热门电子元器件搜索 |
|
HCPL-070L-500E 数据表(PDF) 10 Page - AVAGO TECHNOLOGIES LIMITED |
|
HCPL-070L-500E 数据表(HTML) 10 Page - AVAGO TECHNOLOGIES LIMITED |
10 / 12 page 10 *All typical values at TA = 25˚C, unless otherwise noted. **The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous voltage rating. For the continuous voltage rating refer to the IEC/EN/DIN EN 60747-5-2 Insulation Characteristics Table (if applicable), your equip- ment level safety specification or Avago Application Note 1074 entitled "Optocoupler Input-Output Endurance Voltage." Notes: 1. Pin 5 should be the most negative voltage at the detector side. 2. Each channel. 3. DC CURRENT TRANSFER RATIO (CTR) is defined as the ratio of output collector current, IO, to the forward LED input current, IF, times 100%. 4. Device considered a two-terminal device: pins 1, 2, 3, and 4 shorted together, and pins 5, 6, 7, and 8 shorted together. 5. Measured between pins 1 and 2 shorted together, and pins 3 and 4 shorted together. 6. Common mode transient immunity in a Logic High level is the maximum tolerable (positive) dVCM/dt of the common mode pulse, VCM, to as- sure that the output will remain in a Logic High state (i.e., VO > 2.0 V). Common mode transient immunity in a Logic Low level is the maximum tolerable (negative) dVCM/dt of the common mode pulse, VCM, to assure that the output will remain in a Logic Low state (i.e., VO < 0.8 V). 7. In applications where dV/dt may exceed 50,000 V/µs (such as static discharge) a series resistor, RCC, should be included to protect the detector IC from destructively high surge currents. The recommended value is RCC = 110 Ω. 8. Use of a 0.1 µF bypass capacitor connected between pins 5 and 8 adjacent to the device is recommended. 9. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage > 4500 V rms for 1 second (leakage detec- tion current limit, II-O < 5 µA). 10. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage > 6000 V rms for 1 second (leakage detec- tion current limit, II-O < 5 µA). 11. Measured between the LED anode and cathode shorted together and pins 5 through 8 shorted together. 12. Derate linearly above 65˚C free-air temperature at a rate of 2.3 mW/˚C for the SO-8 package. Package Characteristics Parameter Sym. Device HCPL- Min. Typ.* Max. Units Test Conditions Fig. Note Input-Output VISO 3750 V rms RH ≤ 50%, 4, 9 Momentary t = 1 min., Withstand TA = 25˚C Voltage** Resistance RI-O 1012 Ω VI-O = 500 Vdc 4 (Input-Output) RH ≤ 45% Capacitance CI-O 0.6 pF f = 1 MHz 11 (Input-Output) Input-Input II-I 0.005 µA RH ≤ 45% 5 Insulation VI-I = 500 Vdc Leakage Current Input-Input RI-I 1011 Ω 5 Insulation Leakage Current Capacitance CI-I 270L 0.03 pF 5 (Input-Input) 273L 070L 0.25 073L |
类似零件编号 - HCPL-070L-500E |
|
类似说明 - HCPL-070L-500E |
|
|
链接网址 |
隐私政策 |
ALLDATASHEETCN.COM |
ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |