数据搜索系统,热门电子元器件搜索
  Chinese▼

Delete All
ON OFF
ALLDATASHEETCN.COM

X  

预览 PDF HTML

DR3100-1 Datasheet(数据表) 4 Page - Murata Manufacturing Co., Ltd.

部件型号  DR3100-1
说明  433.92 MHz Transceiver Module
下载  5 Pages
Scroll/Zoom Zoom In 100% Zoom Out
制造商  MURATA [Murata Manufacturing Co., Ltd.]
网页  http://www.murata.com
标志 

DR3100-1 Datasheet(HTML) 4 Page - Murata Manufacturing Co., Ltd.

   
Zoom Inzoom in Zoom Outzoom out
 4 page
background image
6
GND
This is a ground pin.
7
GND
This is a ground pin.
8
LPF ADJ
This pin is the receiver low-pass filter bandwidth adjust, and is connected directly to the transceiver LPFADJ pin.
R6 on the circuit board (12 K) is connected between LPFADJ and ground will be in parallel with any external resis-
tor connected to LPF ADJ. The filter bandwidth is set by the parallel resistance of R6 and the external resistor (if
used). The equivalent resistor value can range from 12 K to 820 ohms, providing a filter 3 dB bandwidth fLPF from
120 kHz to 1.8 MHz. The 3 dB filter bandwidth is determined by:
fLPF = 1445/ (12*RLPF/(12 + RLPF)), where RLPF is in kilohms, and fLPF is in kHz
A ±5% resistor should be used to set the filter bandwidth. This will providea3dB filter bandwidth between fLPF
and 1.3* fLPF with variations in supply voltage, temperature, etc. The filter provides a three-pole, 0.05 degree
equiripple phase response. The peak drive current available from RXDATA increases in proportion to the filter
bandwidth setting. As shipped, the transceiver module is set up for nominal 115.2 kbps operation. Refer to sec-
tions 1.4.3, 2.5.1 and 2.6.1 in the ASH Transceiver Designer’s Guide for additional information on data rate adjust-
ments.
9
VCC
This is the positive supply voltage pin for the module. The operating voltage range is 2.7 to 3.5 Vdc. It is also pos-
sible to use Pin 1 as the Vcc input. Please refer to the Pin 1 description above.
10
GND
This is a ground pin.
11
CTR1
CTR1 is connected to the CNTRL1 control pin on the transceiver. CTR1 and CTR0 select the transceiver operat-
ing modes. CTR1 and CTR0 both high place the unit in the receive mode. CTR1 and CTR0 both low place the unit
in the power-down (sleep) mode. CTR1 high and CTR0 low place the unit in the ASK transmit mode. CTR1 low
and CTR0 high place the unit in the OOK transmit mode. CTR1 is a high-impedance input (CMOS compatible).
This pin must be held at a logic level; it cannot be left unconnected. At turn on, the voltage on this pin and CTR0
should rise with VCC until VCC reaches 2.7 Vdc (receive mode). Thereafter, any mode can be selected.
12
CTR0
CTR0 is connected to the CNTRL0 control pin on the transceiver CTR0 is used with CTR1 to control the operating
modes of the transceiver. CTR0 is a high-impedance input (CMOS compatible). This pin must be held at a logic
level; it cannot be left unconnected. At turn on, the voltage on this pin and CTR1 should rise with VCC until VCC
reaches 2.7 Vdc (receive mode). Thereafter, any mode can be selected.
13
RFIO
RFIO is the RF input/output pin. A matching circuit for a 50 ohm load (antenna) is implemented on the circuit
board between this pin and the transceiver SAW filter transducer.
14
RF GND
This pin is the RF ground (return) to be used in conjunction with the RFIO pin. For example, when connecting the
transceiver module to an external antenna, the coaxial cable ground is connected this pin and the coaxial cable
center conductor is connected to RFIO.
4
D a t a In
Da t a O u t
3 V d c
R/T
1 1 5 . 2 k bps A ppl i c a t i on C i r c ui t
4. 3 K
12345
6
7
8
9
10
11
12
D R 3100- 1
2200 p F
0. 001 µ F
13
14




HTML 页

1  2  3  4  5 


数据表 下载




链接网址


Privacy Policy
ALLDATASHEETCN.COM
ALLDATASHEET是否为您带来帮助?  [ DONATE ]  

关于 Alldatasheet    |   广告服务   |   联系我们   |   隐私政策   |   书签   |   链接交换   |   制造商名单
All Rights Reserved© Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  , Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp  |   Russian : Alldatasheetru.com
Korean : Alldatasheet.co.kr   |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com  |   Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl