数据搜索系统,热门电子元器件搜索 |
|
LM3551 数据表(PDF) 11 Page - Texas Instruments |
|
LM3551 数据表(HTML) 11 Page - Texas Instruments |
11 / 23 page LM3551, LM3552 www.ti.com SNVS371C – AUGUST 2005 – REVISED MARCH 2011 APPLICATION INFORMATION LM3551 AND LM3552 FUNCTIONALITY TRUTH TABLE SD (LM3551) or T/F LM3551 Result LM3552 Result EN (LM3552) 1 0 Shut-down Torch Mode 1 1 Shut-down Flash Mode 0 0 Torch Mode Shut-down 0 1 Flash Mode Shut-down The LM3551 has a 1.2M Ω pull-up to VIN on SD and the LM3552 has a 1.2MΩ pull-down to GND on EN. CURRENT SET EQUATIONS The LM3551/2 utilize inline resistors to set the Torch and Flash LED currents. The Torch-Mode current (continuous) and the Flash-Mode current (pulsed) are programmed by placing the appropriately selected resistors between the feedback pin (FB) and FET-T (torch FET) and FET-F (flash FET) pins. Torch-mode is set by utilizes the current through one resistor while Flash-mode is set by utilizes the currents though both current set resistors. The following equations are used to set the LED currents. RTORCH = (1.265V / ITORCH) - RDSON-T (4) RFLASH = (1.265V / (IFLASH- ITORCH)) - RDSON-F (5) RDSON-T= 0.98Ω and RDSON-F = 0.36Ω (6) NOTE Flash LEDs from different manufacturers can have very different continuous and pulse current ratings. See the manufacturers datasheets to ensure that the proper current levels are used to avoid damaging the flash LED. INDUCTOR SELECTION Special care must be taken when selecting an inductor for use in LM3551/2 applications. The inductor should have a current saturation rating that is larger than the worst case peak inductor current of the application to ensure proper operation. Using an inductor with a lower saturation current rating than is required can cause a dramatic drop in the inductance and can derate the maximum output current levels severely. It is worth noting that the output voltage ripple is also affected by the total ripple current in the inductor. The following equations can help give a good approximation as to what the peak inductor current will be for a given application at room temperature (TA = +25°C). IL(average) = [ILED × VOUT-MAX] ÷ [VIN-MIN × Eff.] (7) ΔIL = [VIN × D] ÷ [L × FSW] (8) IL(peak) = IL(ave) + [ΔIL ÷ 2] (9) VOUT-MAX Maximum Output Voltage. Maximum output voltage over temperature with OVP used is 11V (12.4V typically). VIN-MIN Minimum Input Voltage. Recommended minimum input voltage is 3.0V. The LM3551/2 will work down to 2.7V however, use at lower input voltages will required an inductor with a higher saturation current rating. Eff. Converter Efficiency (approx. 85% over input voltage range). D Duty Cycle = 1 - [VIN / VOUT] L Inductance. Recommended inductance value is 4.7µH. FSW Switching Frequency = 1.25MHz Copyright © 2005–2011, Texas Instruments Incorporated Submit Documentation Feedback 11 Product Folder Links: LM3551 LM3552 |
类似零件编号 - LM3551_14 |
|
类似说明 - LM3551_14 |
|
|
链接网址 |
隐私政策 |
ALLDATASHEETCN.COM |
ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |