数据搜索系统,热门电子元器件搜索 |
|
TC100PI-EX-SP 数据表(PDF) 3 Page - MORNSUN Science& Technology Ltd. |
|
TC100PI-EX-SP 数据表(HTML) 3 Page - MORNSUN Science& Technology Ltd. |
3 / 4 page The copyright and authority for the interpretation of the products are reserved by MORNSUN TCx00PI-EX 2013.03.22-A/0 Page 3 of 4 CONNECTION 1. Removable terminal; 2. Cross section area of wiring: 0.5mm 2 ~2.5 mm2 3. The length of bare wire is about 8mm, locked up by the M3 bolt. Application about Surge Protector Connect the ground of protected equipment or case, and ground of surge protectors directly, and connecting wire is as short as possible. Single point grounding can make surge protectors avoid high-voltage between surge protectors and the ground, which makes protection more effectively. Selection guidelines for intrinsically safety explosion protection system 1. The explosion protection grade of the barrier must be not less than that of intrinsically safety explosion protection device in spot. 2. Take in consideration of hazardous end output resistance and loop resistance make sure the barrier output voltage meets the minimum operation voltage requirement of intrinsically safety device in spot. 3. The safety parameters about intrinsically safety end meets: Uo ≤ UI, Io ≤ Iin, Po ≤ Pin Co ≥ Cin, Lo ≥ Lin 4. Select suitable safety barrier which matches the intrinsically safety device in spot according to the power polarity, signal type and transmission mode about the device. 5. Much more protection is required, which can avoid the influence of the leakage current generated by safety barrier on intrinsically safety device in spot. Operation notes 1. Please read the user manual carefully before using. If any questions please contact our technical support department. 2. Please do not use this product in hazardous area. 3. Power supply of this product should be 24VDC. 220VAC is prohibited. To avoid explosion protection function invalid or any failure, disassembling the product is forbidden. APPLICATION CIRCUIT DIAGRAM & PIN DESCRIPTION Hazardous-area Safe-area 485B 485A 1 2 3 4 7 8 5 6 485B 485A 13 14 15 16 1 2 3 4 5 6 TC600PI-EX-SP TC100PI-EX-SP RL RL RL 18~36V DC 18~36V DC 4/ 0~ 20mA 4/ 0~ 20mA 4/0~ 20mA Hazardous-area Safe-area mV mV + - + - + - + - + - + - 11 12 13 14 15 16 + - 11 12 INSTALLATION & DISASSEMBLY Installation DIN35mm standard rail installation: 1.Insert the top of the instrument card in the rail; 2.Push the bottom of the instrument into the rail. Disassembly 1. Use a screwdriver (Width of edge ≤ 6mm), cut in the metal card lock from the underside; 2. Boost up the screwdriver and prize the metal card lock downwards; 3. Pull the instrument out of the rail. 1 2 3 |
类似零件编号 - TC100PI-EX-SP |
|
类似说明 - TC100PI-EX-SP |
|
|
链接网址 |
隐私政策 |
ALLDATASHEETCN.COM |
ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |