数据搜索系统,热门电子元器件搜索 |
|
CS2516 数据表(PDF) 4 Page - Cherry Semiconductor Corporation |
|
CS2516 数据表(HTML) 4 Page - Cherry Semiconductor Corporation |
4 / 6 page 4 Program and Standby Currents: IP = = Å 1µA Standby Current = 4IP = 4µA (typ.) 9V 9.1m½ VCC RP Test Pulse Width: Tp = RdCT x ln(VP) Å 242CTÅ 242 x 4.7µF Å 1.14ms where Rd is the dynamic cycle timer discharge impedance (440½ typ.) and VP = [1n(VP) = 0.55 typ.] Pulse Stretcher: Delay Time: TD = = = Å 1ms where Vd = Schmitt Trigger Upper Threshold (2.5V typ.) and Isrc = Typical source current at the PW pin at the nominal low battery sense threshold of 6.7V. Pulse Width: Tp = CPWRPW ln(VS) Å 0.51 x 0.1µF x 10m½ Å 510ms. and VS = [ln(VS) = 0.51 typ.] Schmitt Trigger Upper Threshold Schmitt Trigger Hysteresis 2.5 x 0.1µF 250µA 2.5CPW 250µA VdCPW Isrc Upper Charge Threshold Lower Discharge Threshold VCC 220 W CT CS2516 Rp 4.7 mF 9.1M W 9V PW OUT Load Switch Rp SENSE CT COM Cpw Rpw 10M W 0.1 mF + + 510 W VCC Applications Information Typical Application Circuit The value of Rp affects standby current, operating current, and the test cycle period. The recommended value is (V+/1µA) where V+ is the fresh battery voltage. Higher values of Rp are not recommended. Minimum recom- mended value is (V+/10µA) which will increase both the standby and operating currents by 10X and reduce the test cycle period by the same factor; the test pulse width will be unaffected. The value of Ct affects both the test cycle period and the test pulse width. Of critical importance is the selection of a low leakage type capacitor; if leakage current exceeds the cycle timer charge current, the timer will not operate. The pulse stretcher components RPW and CPW should be selected such that the delay timer to charge CPW is shorter than the test pulse width programmed by Ct to guarantee operation of the Output. The output is an open-collector transistor which may be used to drive an indicator device directly or to interface to logic family devices. The SENSE input typical 8.5k½ input impedance appears only during the test pulse; otherwise the SENSE input is in a high impedance state. The effective low battery thresh- old voltage can be modified (increased only) by means of a voltage divider placed across the load resistor. This tech- nique can also be used to effectively reduce the threshold tolerance band. Applications Formulae and Typical Values Cycle Timer Period: Tt === Å 33sec., where Vt = Upper Charge Threshold - Lower Charge Threshold (7V typ.) 7 x 4.7µF 1µA 7CT 1µA VTCT IP |
类似零件编号 - CS2516 |
|
类似说明 - CS2516 |
|
|
链接网址 |
隐私政策 |
ALLDATASHEETCN.COM |
ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |