数据搜索系统,热门电子元器件搜索 |
|
DNS10S0A0R16NFD 数据表(PDF) 10 Page - Delta Electronics, Inc. |
|
DNS10S0A0R16NFD 数据表(HTML) 10 Page - Delta Electronics, Inc. |
10 / 16 page DS_DNL10SMD_07182012 10 The amount of power delivered by the module is the voltage at the output terminals multiplied by the output current. When using the trim feature, the output voltage of the module can be increased, which at the same output current would increase the power output of the module. Care should be taken to ensure that the maximum output power of the module must not exceed the maximum rated power (Vo.set x Io.max ≤ P max). Voltage Margining Output voltage margining can be implemented in the DNL modules by connecting a resistor, R margin-up, from the Trim pin to the ground pin for margining-up the output voltage and by connecting a resistor, Rmargin-down, from the Trim pin to the output pin for margining-down. Figure 37 shows the circuit configuration for output voltage margining. If unused, leave the trim pin unconnected. A calculation tool is available from the evaluation procedure, which computes the values of Rmargin-up and Rmargin-down for a specific output voltage and margin percentage. Vo On/Off Vin GND Trim Q2 Q1 Rmargin-up Rmargin-down Rtrim Figure 34: Circuit configuration for output voltage margining Voltage Tracking The DNL family was designed for applications that have output voltage tracking requirements during power-up and power-down. The devices have a TRACK pin to implement three types of tracking method: sequential start-up, simultaneous and ratio-metric. TRACK simplifies the task of supply voltage tracking in a power system by enabling modules to track each other, or any external voltage, during power-up and power-down. By connecting multiple modules together, customers can get multiple modules to track their output voltages to the voltage applied on the TRACK pin. FEATURE DESCRIPTIONS (CON.) Table 1 provides Rtrim values required for some common output voltages, while Table 2 provides values of external voltage source, Vtrim, for the same common output voltages. By using a 1% tolerance trim resistor, set point tolerance of ±2% can be achieved as specified in the electrical specification. Table 1 VO (V) Rtrim (KΩ) 0.7525 Open 1.0 41.424 1.2 22.464 1.5 13.047 1.8 9.024 2.0 7.416 2.5 5.009 3.3 3.122 5.0 1.472 Table 2 VO (V) Vtrim (V) 0.7525 Open 1.0 0.6835 1.2 0.670 1.5 0.650 1.8 0.630 2.0 0.6168 2.5 0.583 3.3 0.530 5.0 0.4167 |
类似零件编号 - DNS10S0A0R16NFD |
|
类似说明 - DNS10S0A0R16NFD |
|
|
链接网址 |
隐私政策 |
ALLDATASHEETCN.COM |
ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |