数据搜索系统,热门电子元器件搜索 |
|
H5PS5182GFRG7L 数据表(PDF) 59 Page - Hynix Semiconductor |
|
H5PS5182GFRG7L 数据表(HTML) 59 Page - Hynix Semiconductor |
59 / 64 page Rev.1.7 / Feb. 2013 59 H5PS5162GFR series 24. These parameters are measured from a command/address signal (CKE, CS, RAS, CAS, WE, ODT, BA0, A0, A1, etc.) transition edge to its respective clock signal (CK/CK) crossing. The spec values are not affected by the amount of clock jitter applied (i.e. tJIT(per), tJIT(cc), etc.), as the setup and hold are relative to the clock signal crossing that latches the command/address. That is, these parameters should be met whether clock jitter is present or not. 25. These parameters are measured from a data strobe signal ((L/U/R)DQS/DQS) crossing to its respective clock signal (CK/CK) crossing. The spec values are not affected by the amount of clock jitter applied (i.e. tJIT(per), tJIT(cc), etc.), as these are relative to the clock signal crossing. That is, these parameters should be met whether clock jitter is present or not. 26. These parameters are measured from a data signal ((L/U) DM, (L/U) DQ0, (L/U) DQ1, etc.) transition edge to its respective data strobe signal ((L/U/R)DQS/DQS) crossing. 27. For these parameters, the DDR2 SDRAM device is characterized and verified to support tnPARAM = RU{tPARAM / tCK(avg)}, which is in clock cycles, assuming all input clock jitter specifications are satisfied. For example, the device will support tnRP = RU {tRP / tCK(avg)}, which is in clock cycles, if all input clock jitterspecifications are met. This means: For DDR2-1066 7-7-7, of which tRP = 13.125ns, the device will support tnRP =RU{tRP / tCK(avg)} = 7, i.e. as long as the input clock jitter specifications are met, Pre- charge command at Tm and Active command at Tm+7 is valid even if (Tm+7 - Tm) is less than 13.127ns due to input clock jitter. 28. Specific Note 28 tDAL nCK = WR nCK + tnRP nCK = WR + RUtRP ps / tCK(avg) ps, where WR is the value programmed in the mode register set and RU stands for round up. Example: For DDR2-1066 7-7-7 at tCK(avg) = 1.875 ns with WR programmed to 8 nCK, tDAL = 8 + RU 13.125 ns / 1.875 ns nCK = 8 + 7 nCK = 15 nCK 29.New units, ‘tCK(avg)’ and ‘nCK’, are introduced in DDR2-1066. Unit ‘tCK(avg)’ represents the actual tCK(avg) of the input clock under operation. Unit ‘nCK’ represents one clock cycle of the input clock, counting the actual clock edges. ex) tXP = 3 [nCK] means; if Power Down exit is registered at Tm, an Active command may be registered at Tm+3, even if (Tm+3 - Tm) is 3 x tCK(avg) + tERR(3per),min. 30. Input clock jitter spec parameter. These parameters and the ones in the table below are referred to as 'input clock jitter spec parameters' and these parameters apply to DDR2-1066. The jitter specified is a ran- dom jitter meeting a Gaussian distribution. |
类似零件编号 - H5PS5182GFRG7L |
|
类似说明 - H5PS5182GFRG7L |
|
|
链接网址 |
隐私政策 |
ALLDATASHEETCN.COM |
ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |