数据搜索系统,热门电子元器件搜索
  Chinese▼

Delete All
ON OFF
ALLDATASHEETCN.COM

X  

预览 PDF Download HTML

N25Q032A13ESC40F Datasheet(数据表) 20 Page - Micron Technology

部件型号  N25Q032A13ESC40F
说明  32-Mbit 3 V, multiple I/O, 4-Kbyte subsector erase, XiP enabled, serial flash memory with 108 MHz SPI bus interface
下载  153 Pages
Scroll/Zoom Zoom In 100% Zoom Out
制造商  MICRON [Micron Technology]
网页  http://www.micron.com
标志 

N25Q032A13ESC40F Datasheet(HTML) 20 Page - Micron Technology

Zoom Inzoom in Zoom Outzoom out
 20 page
background image
SPI Protocols
N25Q032 - 3 V
20/153
Micron Technology, Inc., reserves the right to change products or specifications without notice.
©2010 Micron Technology, Inc. All rights reserved.
4
SPI Protocols
The N25Q032 memory can work with 3 different Serial protocols:
Extended SPI protocol.
Dual I/O SPI (DIO-SPI) protocol.
Quad I/O SPI (QIO-SPI) protocol.
It is possible to choose among the three protocols by means of user volatile or non-volatile
configuration bits.It's not possible to mix Extended SPI, DIO-SPI, and QIO-SPI protocols.
The device can operate in XIP mode in all 3 protocols.
4.1
Extended SPI protocol
This is an extension of the standard (legacy) SPI protocol. Instructions are transmitted on a
single data line (DQ0), while addresses and data are transmitted by one, two or four data
lines (DQ0, DQ1, W/VPP(DQ2) and HOLD / (DQ3) according to the instruction.
When used in the Extended SPI protocol, these devices can be driven by a micro controller
in either of the two following modes:
CPOL=0, CPHA=0
CPOL=1, CPHA=1
Please refer to the SPI modes for a detailed description of these two modes
4.2
Dual I/O SPI (DIO-SPI) protocol
Dual I/O SPI (DIO-SPI) protocol: instructions, addresses and I/O data are always
transmitted on two data lines (DQ0 and DQ1).
Also when in DIO-SPI mode, the device can be driven by a micro controller in either of the
two following modes:
CPOL= 0, CPHA= 0
CPOL= 1, CPHA= 1
Please refer to the SPI modes for a detailed description of these two modes.
Note:
Extended SPI protocol Dual I/O instructions allow only address and data to be transmitted
over two data lines. However, DIO-SPI allows instructions, addresses, and data to be
transmitted on two data lines.
This mode can be set using two ways
Volatile: by setting bit 6 of the VECR to 0. The device enters DIO-SPI protocol
immediately after the Write Enhanced Volatile Configuration Register sequence
completes. The device returns to the default working mode (defined by NVCR) on
power on.
Default/ Non-Volatile: This is default mode on power-up. By setting bit 2 of the NVCR
to 0. The device enters DIO-SPI protocol on the subsequent power-on. After all
subsequent power-on sequences, the device still starts in DIO-SPI protocol unless bit 2
of NVCR is set to 1 (default value, corresponding to Extended SPI protocol) or bit 3 of
NVCR is set to 0 (corresponding to QIO-SPI protocol).




HTML 页

1  2  3  4  5  6  7  8  9  10  11  12  13  14  15  16  17  18  19  20  21  22  23  24  25  26  27  28  29  30  31  32  33  34  35  36  37  38  39  40  41  42  43  44  45  46  47  48  49  50  51  52  53  54  55  56  57  58  59  60  61  62  63  64  65  66  67  68  69  70  71  72  73  74  75  76  77  78  79  80  81  82  83  84  85  86  87  88  89  90  91  92  93  94  95  96  97  98  99  100   ...More


数据表 下载




链接网址


Privacy Policy
ALLDATASHEETCN.COM
ALLDATASHEET是否为您带来帮助?  [ DONATE ]  

关于 Alldatasheet    |   广告服务   |   联系我们   |   隐私政策   |   书签   |   链接交换   |   制造商名单
All Rights Reserved© Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  , Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp  |   Russian : Alldatasheetru.com
Korean : Alldatasheet.co.kr   |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com  |   Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl