ST16C2550CJ44 datasheet(6/37 Pages) EXAR

部件名	ST16C2550CJ44

功能描述	Up to 4 Mbps with external clock of 64 MHz

Download	37 Pages

Scroll/Zoom	100%

制造商	EXAR [Exar Corporation]

网页	http://www.exar.com

标志

6 / 37 page

ST16C2550

6

2.97V TO 5.5V DUART WITH 16-BYTE FIFO

REV. 4.4.1

NOTE: Pin type: I=Input, O=Output, IO= Input/output, OD=Output Open Drain.

CTSB#

25

28

23

I

UART channel B Clear-to-Send (active low) or general

purpose input. This input should be connected to VCC

when not used. This input has no effect on the UART.

DTRB#

34

38

35

O

UART channel B Data-Terminal-Ready (active low) or

general purpose output. If it is not used, leave it uncon-

nected.

DSRB#

22

25

20

I

UART channel B Data-Set-Ready (active low) or general

purpose input. This input should be connected to VCC

when not used. This input has no effect on the UART.

CDB#

19

21

16

I

UART channel B Carrier-Detect (active low) or general

purpose input. This input should be connected to VCC

when not used. This input has no effect on the UART.

RIB#

23

26

21

I

UART channel B Ring-Indicator (active low) or general

purpose input. This input should be connected to VCC

when not used. This input has no effect on the UART.

OP2B#

13

15

9

O

Output Port 2 Channel B - The output state is defined by

the user and through the software setting of MCR[3].

INTB is set to the active mode and OP2B# output to a

logic 0 when MCR[3] is set to a logic 1. INTB is set to the

three state mode and OP2B# to a logic 1 when MCR[3] is

set to a logic 0. See MCR[3]. This output should not be

used as a general output else it will disturb the INTB out-

put functionality. If it is not used, leave it unconnected.

ANCILLARY SIGNALS

XTAL1

16

18

13

I

Crystal or external clock input.

XTAL2

17

19

14

O

Crystal or buffered clock output.

RESET

35

39

36

I

Reset (active high) - A longer than 40 ns logic 1 pulse on

this pin will reset the internal registers and all outputs.

The UART transmitter output will be held at logic 1, the

receiver input will be ignored and outputs are reset during

reset period (see External Reset Conditions).

VCC

40

44

42

Pwr

2.97V to 5.5V power supply. All inputs are 5V tolerant for

devices with top marking of "A2 YYWW" and newer.

GND

20

22

17

Pwr

Power supply common, ground.

N.C.

-

12, 24, 25,

37

No Connection. These pins are open, but typically, should

be connected to GND for good design practice.

Pin Description

NAME

40-PDIP

PIN #

44-PLCC

PIN #

48-TQFP

PIN #

TYPE

DESCRIPTION

类似零件编号 - ST16C2550CJ44

制造商	部件名	数据表	功能描述
Exar Corporation	ST16C2550CJ44	443Kb / 34P	DUAL UART WITH 16-BYTE TRANSMIT AND RECEIVE FIFOS
Exar Corporation	ST16C2550CJ44	661Kb / 39P	2.97V TO 5.5V DUART WITH 16-BYTE FIFO

More results

类似说明 - ST16C2550CJ44

制造商	部件名	数据表	功能描述
STMicroelectronics	STM32F303X6	1Mb / 115P	Up to 64 Kbytes of Flash memory October 2016 Rev 5
New Japan Radio	NJU6359	330Kb / 11P	SERIAL I/O REAL TIME CLOCK WITH WAKE-UP OUTPUT for EXTERNAL CLOCK
List of Unclassifed Man...	ICS551MI	199Kb / 9P	Input/Output clock frequency up to 160 MHz
NXP Semiconductors	KE1XZP48M48SF0	1Mb / 82P	Kinetis KE1xZ with up to 64 KB Flash Rev. 3, 06/2020
List of Unclassifed Man...	ST-85540	114Kb / 1P	64 MBPS INTERFACE TRANSFORMERS
ams AG	AS8223	74Kb / 2P	Data transfer up to 10 Mbps
STMicroelectronics	M24C64-A125	608Kb / 40P	Automotive 64-Kbit serial IC bus EEPROM with 1 MHz clock
Rohm	BD1754HFN	379Kb / 19P	Constant Current LED Driver with 64 Dimming Steps for up to 4 LEDs
QUARTZCOM the communica...	MCO-1S-PE-6P	124Kb / 1P	SMD Clock Oscillator LVPECL Output frequency up to 320 MHz
Rohm	BD1754HFN-TR	379Kb / 19P	Constant Current LED Driver with 64 Dimming Steps for up to 4 LEDs