数据搜索系统,热门电子元器件搜索 |
|
74ACT715-RPC 数据表(PDF) 2 Page - Fairchild Semiconductor |
|
74ACT715-RPC 数据表(HTML) 2 Page - Fairchild Semiconductor |
2 / 14 page www.fairchildsemi.com 2 Logic Block Diagram Pin Description There are a Total of 13 inputs and 5 outputs on the ACT715. Data Inputs D0–D7: The Data Input pins connect to the Address Register and the Data Input Register. ADDR/DATA: The ADDR/DATA signal is latched into the device on the falling edge of the LOAD signal. The signal determines if an address (0) or data (1) is present on the data bus. L/HBYTE: The L/HBYTE signal is latched into the device on the falling edge of the LOAD signal. The signal deter- mines if data will be read into the 8 LSB’s (0) or the 4 MSB’s (1) of the Data Registers. A 1 on this pin when an ADDR/DATA is a 0 enables Auto-Load Mode. LOAD: The LOAD control pin loads data into the Address or Data Registers on the rising edge. ADDR/DATA and L/ HBYTE data is loaded into the device on the falling edge of the LOAD. The LOAD pin has been implemented as a Schmitt trigger input for better noise immunity. CLOCK: System CLOCK input from which all timing is derived. The clock pin has been implemented as a Schmitt trigger for better noise immunity. The CLOCK and the LOAD signal are asynchronous and independent. Output state changes occur on the falling edge of CLOCK. CLR: The CLEAR pin is an asynchronous input that initial- izes the device when it is HIGH. Initialization consists of setting all registers to their mask programmed values, and initializing all counters, comparators and registers. The CLEAR pin has been implemented as a Schmitt trigger for better noise immunity. A CLEAR pulse should be asserted by the user immediately after power-up to ensure proper initialization of the registers—even if the user plans to (re)program the device. Note: A CLEAR pulse will disable the CLOCK on the ACT715 and will enable the CLOCK on the ACT715-R. ODD/EVEN: Output that identifies if display is in odd (HIGH) or even (LOW) field of interlace when device is in interlaced mode of operation. In noninterlaced mode of operation this output is always HIGH. Data can be serially scanned out on this pin during Scan Mode. VCSYNC: Outputs Vertical or Composite Sync signal based on value of the Status Register. Equalization and Serration pulses will (if enabled) be output on the VCSYNC signal in composite mode only. VCBLANK: Outputs Vertical or Composite Blanking signal based on value of the Status Register. HBLHDR: Outputs Horizontal Blanking signal, Horizontal Gating signal or Cursor Position based on value of the Sta- tus Register. HSYNVDR: Outputs Horizontal Sync signal, Vertical Gat- ing signal or Vertical Interrupt signal based on value of Sta- tus Register. |
类似零件编号 - 74ACT715-RPC |
|
类似说明 - 74ACT715-RPC |
|
|
链接网址 |
隐私政策 |
ALLDATASHEETCN.COM |
ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |