LTM8033 datasheet(9/22 Pages) LINER

部件名	LTM8033

功能描述	Inverting or SEPIC 關Module DC/DC Converter with up to 700mA Output Current

Download	22 Pages

Scroll/Zoom	100%

制造商	LINER [Linear Technology]

网页	http://www.linear.com

标志

9 / 22 page

LTM8045

9

8045fa

For more information www.linear.com/8045

PIN FUNCTIONS

VOUT– (Bank 1): VOUT– is the negative output of the

LTM8045. Apply an external capacitor between VOUT+and

VOUT–. Tie this net to GND to configure the LTM8045 as

a positive output SEPIC regulator.

VOUT+ (Bank 2): VOUT+ is the positive output of the

LTM8045. Apply an external capacitor between VOUT+ and

VOUT–. Tie this net to GND to configure the LTM8045 as

a negative output inverting regulator.

GND (Bank 3): Tie these GND pins to a local ground plane

below the LTM8045 and the circuit components. GND

MUST BE CONNECTED EITHER TO VOUT+ OR VOUT– FOR

PROPER OPERATION. In most applications, the bulk of

the heat flow out of the LTM8045 is through these pads,

so the printed circuit design has a large impact on the

thermal performance of the part. See the PCB Layout and

Thermal Considerations sections for more details. Return

the feedback divider (RFB) to this net.

VIN(Bank4):TheVINpinsuppliescurrenttotheLTM8045’s

internal regulator and to the internal power switch. This

pin must be locally bypassed with an external, low ESR

capacitor.

FB (Pin A3): If configured as a SEPIC, the LTM8045

regulates its FB pin to 1.215V. Apply a resistor between

FB and VOUT+. Its value should be RFB = [(VOUT – 1.215)/

0.0833]kΩ. If the LTM8045 is configured as an inverting

converter,theLTM8045regulatestheFBpinto5mV.Apply

a resistor between FB and VOUT– of value RFB = [(|VOUT|

+ 0.005)/0.0833]kΩ.

SYNC (Pin E1): To synchronize the switching frequency

to an outside clock, simply drive this pin with a clock. The

high voltage level of the clock needs to exceed 1.3V, and

the low level should be less than 0.4V. Drive this pin to

less than 0.4V to revert to the internal free running clock.

Ground this pin if the SYNC function is not used. See the

Applications Information section for more information.

SS(PinF1):Placeasoft-startcapacitorhere.Uponstart-up,

the SS pin will be charged by a (nominally) 275k resistor

to about 2.2V.

RT (Pin G1): The RT pin is used to program the switching

frequency of the LTM8045 by connecting a resistor from

this pin to ground. The necessary resistor value for the

LTM8045isdeterminedbytheequationRT=(91.9/fOSC)–1,

where fOSC is the typical switching frequency in MHz and

RT is in kΩ. Do not leave this pin open.

RUN (Pin G3): This pin is used to enable/disable the chip

and restart the soft-start sequence. Drive below 1.235V

to disable the chip. Drive above 1.385V to activate chip

and restart the soft-start sequence. Do not float this pin.

类似零件编号 - LTM8033

制造商	部件名	数据表	功能描述
Linear Technology	LTM8033	274Kb / 24P	Ultralow Noise EMC 36VIN, 3A DC/DC 關Module Regulator
	LTM8033	371Kb / 28P	Ultralow EMI 28VIN, 6A DC/DC 關Module Regulator
	LTM8033	525Kb / 28P	EN55022B Compliant 36VIN, 15VOUT, 5A, DC/DC Module Regulator
	LTM8033	347Kb / 20P	3.1VIN to 32VIN Isolated 關Module DC/DC Converter
	LTM8033	469Kb / 28P	de36VIN, 5A 關Module Regulator with 5-Output Configurable LDO Array

More results

类似说明 - LTM8033

制造商	部件名	数据表	功能描述
Linear Technology	LTM8045	289Kb / 22P	Inverting or SEPIC Module DC/DC Converter with Up to 700mA Output Current
Linear Technology	LTM8049	1Mb / 20P	Dual SEPIC or Inverting 關Module DC/DC Converter
Linear Integrated Syste...	LTM8049	1Mb / 18P	Dual SEPIC or Inverting Module DC DC Converter
Linear Technology	LTM8008	245Kb / 16P	72VIN, 6 Output DC/DC SEPIC 關Module Regulator
Linear Technology	LT8582	368Kb / 8P	Dual 3A Boost/Inverting/SEPIC DC/DC Converter
Torex Semiconductor	XC9519	1Mb / 38P	Dual Output Step-Up/Inverting DC/DC Converter
Linear Technology	LT8582	454Kb / 36P	Dual 3A Boost/Inverting/SEPIC DC/DC Converter with Fault Protection
Panasonic Semiconductor	AN8014S	151Kb / 18P	Step-down, step-up, or inverting DC-DC converter control IC
STMicroelectronics	STOD1412	532Kb / 21P	Step-up and inverting DC-DC converter
Linear Technology	LTM8008	250Kb / 16P	72VIN, 6 Output DC/DC SEPIC Module Regulator