数据搜索系统,热门电子元器件搜索 |
|
ADM213 数据表(PDF) 10 Page - Analog Devices |
|
ADM213 数据表(HTML) 10 Page - Analog Devices |
10 / 12 page ADM205–ADM211/ADM213 REV. 0 –10– Transmitter (Driver) Section The drivers convert TTL/CMOS input levels into EIA-232-E output levels. With VCC = +5 V and driving a typical EIA-232-E load, the output voltage swing is ±9 V. Even under worst case conditions the drivers are guaranteed to meet the ±5 V EIA-232-E minimum requirement. The input threshold levels are both TTL and CMOS compat- ible with the switching threshold set at VCC/4. With a nominal VCC = 5 V the switching threshold is 1.25 V typical. Unused in- puts may be left unconnected, as an internal 400 k Ω pull-up re- sistor pulls them high forcing the outputs into a low state. As required by the EIA-232-E standard, the slew rate is limited to less than 30 V/ µs without the need for an external slew limit- ing capacitor and the output impedance in the power-off state is greater than 300 Ω. Receiver Section The receivers are inverting level shifters which accept EIA-232-E input levels ( ±5 V to ±15 V) and translate them into 5 V TTL/ CMOS levels. The inputs have internal 5 k Ω pull-down resistors to ground and are also protected against overvoltages of up to ±30 V. The guaranteed switching thresholds are 0.8 V mini- mum and 2.4 V maximum which are well within the ±3 V EIA-232-E requirement. The low level threshold is deliberately positive as it ensures that an unconnected input will be inter- preted as a low level. The receivers have Schmitt trigger inputs with a hysteresis level of 0.5 V. This ensures error-free reception for both noisy inputs and for inputs with slow transition times. Shutdown (SD) The ADM205, ADM206, ADM211 and ADM213 feature a control input which may be used to disable the part and reduce the power consumption to less than 5 µW. This is very useful in battery operated systems. During shutdown the charge pump is turned off, the transmitters are disabled and all receivers except R4 and R5 on the ADM213 are put into a high-impedance dis- abled state. Receivers R4 and R5 on the ADM213 remain en- abled during shutdown. This feature allows monitoring external activity such as ring indicator monitoring while the device is in a low power shutdown mode. The shutdown control input is ac- tive high on all parts except the ADM213 where it is active low. Refer to Tables II and III. Enable Input The ADM205, ADM209, ADM211, and ADM213 feature an enable input used to enable or disable the receiver outputs. The enable input is active low on the ADM205, ADM209, ADM211 and active-high on the ADM213. Refer to Tables II and III. When disabled, all receiver outputs are placed in a high imped- ance state. This function allows the outputs to be connected di- rectly to a microprocessor data bus. It can also be used to allow receivers from different devices to share a common data line. The timing diagram for the enable function is shown in Figure 25. T EN T DIS 3V 0V R OUT 3.5V 0.8V V OH – 0.1V V VOL + 0.1V EN * * POLARITY OF EN IS REVERSED FOR ADM213 Figure 25. Enable Timing APPLICATION HINTS Driving Long Cables In accordance with the EIA-232-E standard, long cables are permissible provided that the total load capacitance does not ex- ceed 2500 pF. For longer cables which do exceed this, then it is possible to trade off baud rate vs. cable length. Large load ca- pacitances cause a reduction in slew rate, and hence the maximum transmission baud rate is decreased. The ADM205–ADM211 and ADM213 are designed so that the slew rate reduction with in- creasing load capacitance is minimized. For the receivers, it is important that a high level of noise immu- nity be inbuilt so that slow rise and fall times do not cause mul- tiple output transitions as the signal passes slowly through the transition region. The ADM205–ADM211 and ADM213 have 0.5 V of hysteresis to guard against this. This ensures that, even in noisy environments, error-free reception can be achieved. High Baud Rate Operation The ADM205–ADM211 and ADM213 feature high slew rates permitting data transmission at rates well in excess of the EIA-232-E specification. The drivers maintain ±5 V signal levels at data rates up to 120-kB/s under worst-case loading conditions. |
类似零件编号 - ADM213 |
|
类似说明 - ADM213 |
|
|
链接网址 |
隐私政策 |
ALLDATASHEETCN.COM |
ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |