数据搜索系统,热门电子元器件搜索 |
|
AD824AR-14-3V 数据表(PDF) 11 Page - Analog Devices |
|
AD824AR-14-3V 数据表(HTML) 11 Page - Analog Devices |
11 / 16 page AD824 REV. A –11– A current-limiting resistor should be used in series with the in- put of the AD824 if there is a possibility of the input voltage ex- ceeding the positive supply by more than 300 mV or if an input voltage will be applied to the AD824 when ±V S = 0. The ampli- fier will be damaged if left in that condition for more than 10 seconds. A 1 k Ω resistor allows the amplifier to withstand up to 10 volts of continuous overvoltage and increases the input volt- age noise by a negligible amount. Input voltages less than –VS are a completely different story. The amplifier can safely withstand input voltages 20 volts below the minus supply voltage as long as the total voltage from the positive supply to the input terminal is less than 36 volts. In ad- dition, the input stage typically maintains picoamp level input currents across that input voltage range. OUTPUT CHARACTERISTICS The AD824’s unique bipolar rail-to-rail output stage swings within 15 mV of the positive and negative supply voltages. The AD824’s approximate output saturation resistance is 100 Ω for both sourcing and sinking. This can be used to estimate output saturation voltage when driving heavier current loads. For instance, the saturation voltage will be 0.5 volts from either supply with a 5 mA current load. For load resistances over 20 k Ω, the AD824’s input error voltage is virtually unchanged until the output voltage is driven to 180 mV of either supply. If the AD824’s output is overdriven so as to saturate either of the output devices, the amplifier will recover within 2 µs of its input returning to the amplifier’s linear operating region. Direct capacitive loads will interact with the amplifier’s effective output impedance to form an additional pole in the amplifier’s feedback loop, which can cause excessive peaking on the pulse response or loss of stability. Worst case is when the amplifier is used as a unity gain follower. Figures 5 and 7 show the AD824’s pulse response as a unity gain follower driving 220 pF. Configu- rations with less loop gain, and as a result less loop bandwidth, will be much less sensitive to capacitance load effects. Noise gain is the inverse of the feedback attenuation factor provided by the feedback network in use. Figure 30 shows a method for extending capacitance load drive capability for a unity gain follower. With these component val- ues, the circuit will drive 5,000 pF with a 10% overshoot. 8 4 0.01 µF 20pF 20k Ω 100 Ω V OUT +V S –V S 0.01 µF C L 1/4 AD824 V I N Figure 30. Extending Unity Gain Follower Capacitive Load Capability Beyond 350 pF APPLICATION NOTES INPUT CHARACTERISTICS In the AD824, n-channel JFETs are used to provide a low offset, low noise, high impedance input stage. Minimum input common-mode voltage extends from 0.2 V below –VS to 1 V less than +VS. Driving the input voltage closer to the positive rail will cause a loss of amplifier bandwidth. The AD824 does not exhibit phase reversal for input voltages up to and including +VS. Figure 29a shows the response of an AD824 voltage follower to a 0 V to +5 V (+VS) square wave in- put. The input and output are superimposed. The output tracks the input up to +VS without phase reversal. The reduced band- width above a 4 V input causes the rounding of the output wave form. For input voltages greater than +VS, a resistor in series with the AD824’s noninverting input will prevent phase reversal at the expense of greater input voltage noise. This is illustrated in Figure 29b. 10 0% 100 90 1V 1V 10µs 1V 10 0% 100 90 1V 2µs 1V GND GND +VS +5V RP VOUT VIN Figure 29. (a) Response with RP = 0; VIN from 0 to +VS (b) VIN = 0 to + VS + 200 m V VOUT = 0 to + VS RP = 49.9 kΩ Since the input stage uses n-channel JFETs, input current dur- ing normal operation is positive; the current flows out from the input terminals. If the input voltage is driven more positive than +VS – 0.4 V, the input current will reverse direction as internal device junctions become forward biased. This is illustrated in Figure 9. (b) (a) |
类似零件编号 - AD824AR-14-3V |
|
类似说明 - AD824AR-14-3V |
|
|
链接网址 |
隐私政策 |
ALLDATASHEETCN.COM |
ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |