数据搜索系统,热门电子元器件搜索 |
|
AD7853 数据表(PDF) 11 Page - Analog Devices |
|
AD7853 数据表(HTML) 11 Page - Analog Devices |
11 / 34 page REV. B –11– AD7853/AD7853L STATUS REGISTER The arrangement of the status register is shown below. The status register is a read-only register and contains 16 bits of data. The status register is selected by first writing to the control register and putting two 1s in RDSLT1 and RDSLT0. The function of the bits in the status register are described below. The power-up status of all bits is 0. WRITE TO CONTROL REGISTER SETTING RDSLT0 = RDSLT1 = 1 START READ STATUS REGISTER Figure 6. Flowchart for Reading the Status Register MSB ZERO BUSY ZERO ZERO ZERO ZERO PMGT1 PMGT0 RDSLT1 RDSLT0 2/ 3 MODE X CALMD CALSLT1 CALSLT0 STCAL LSB Status Register Bit Function Descriptions Bit Mnemonic Comment 15 ZERO This bit is always 0. 14 BUSY Conversion/Calibration Busy Bit. When this bit is 1, it indicates that there is a conversion or calibration in progress. When this bit is 0, no conversion or calibration is in progress. 13 ZERO These four bits are always 0. 12 ZERO 11 ZERO 10 ZERO 9 PMGT1 Power Management Bits. These bits, along with the SLEEP pin, will indicate whether or not the part is in a 8 PMGT0 power-down mode. See Table VI in Power-Down Section for description. 7 RDSLT1 Both of these bits are always 1, indicating it is the status register that is being read. See Table II. 6 RDSLT0 52/ 3 MODE Interface Mode Select Bit. With this bit at 0, the device is in Interface Mode 2. With this bit at 1, the device is in Interface Mode 1. This bit is reset to 0 after every read cycle. 4 X Don’t care bit. 3 CALMD Calibration Mode Bit. A 0 in this bit indicates a self-calibration is selected; a 1 in this bit indicates a system calibration is selected (see Table III). 2 CALSLT1 Calibration Selection Bits and Start Calibration Bit. The STCAL bit is read as a 1 if a calibration is in 1 CALSLT0 progress and as a 0 if no calibration is in progress. The CALSLT1 and CALSLT0 bits indicate 0 STCAL which of the calibration registers are addressed for reading and writing (see section on the Calibration Registers for more details). |
类似零件编号 - AD7853 |
|
类似说明 - AD7853 |
|
|
链接网址 |
隐私政策 |
ALLDATASHEETCN.COM |
ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |