数据搜索系统,热门电子元器件搜索 |
|
D-300-08CS1108 数据表(PDF) 3 Page - PANDUIT CORP. |
|
D-300-08CS1108 数据表(HTML) 3 Page - PANDUIT CORP. |
3 / 7 page CUSTOMER DRAWING Tyco Electronics 305 Constitution Dr Menlo Park, CA 94025, U.S.A. TITLE: CAP, SPLICE ENCAPSULATION Unless otherwise specified dimensions are in millimeters. [Inches dimensions are shown in brackets] Raychem Devices DOCUMENT NO.: D-300-08/-12/-18 TOLERANCES: 0.00 N/A 0.0 N/A 0 N/A ANGLES: N/A ROUGHNESS IN MICRON Tyco Electronics reserves the right to amend this drawing at any time. Users should evaluate the suitability of the product for their application. REV: B DATE: 31-July-08 DRAWN BY: M. FORONDA CAGE CODE: 06090 REPLACES: D010044 ECO NUMBER: 08-018889 SCALE: NTS SIZE: A SHEET: 3 of 7 © 2008 Tyco Electronics Corporation. All rights reserved If this document is printed it becomes uncontrolled. Check for the latest revision. 4.3.4.2. Procedure B: Three specimens, prepared and measured in accordance with 4.3.1, shall be conditioned for 1000 hours in a 150 ± 3 °C (302 ± 5°F) mechanical-convection oven in which air passes the specimens at a velocity of 100 to 200 feet per minute. After conditioning, the specimens shall be removed from the oven, cooled to room temperature, and tested for tensile strength and ultimate elongation in accordance with 4.3.1. 4.2.1 Solvent Resistance: Three specimens, prepared and measured in accordance with 4.3.1, shall be completely immersed in each of the solvents listed in the applicable section of Table 1 for 24 hours at 25 ± 3 °C (77 ± 5°F). The volume of the fluid shall be not less than 20 times that of the specimens. After conditioning, the specimens shall be lightly wiped, and then air-dried for 30 to 60 minutes at room temperature. The specimens shall then be tested for tensile strength and ultimate elongation in accordance with 4.3.1. 4.3 Test Procedures – Finished Caps 4.3.1 Test Assembles: Part D-300-12 shall be used to qualify D-300-08, D-300-12 and D-300-18. Fifty-five specimens shall be made by connecting two wires, MIL- 16878/4-14; with a suitable crimp connector. Wires shall be 10 ± 1 inches in length. The caps shall be applied in accordance with Thermofit Assembly Procedure D-300-08/-12/-18. 4.3.2 Dimensions and Dimensional Recovery: Five specimens, as supplied, shall be measured for dimensions in accordance with ASTM D 876. The specimens shall then be conditioned for ten minutes in a 200 ± 5 °C (392 ± 9 °F) oven, quenched in water in less than 35°C (95°F) for at least 30 seconds, wiped dry, and the appropriate measurements taken. 4.3.3 Insulation Resistance: The specimens shall be immersed to within 3 inches of the lead ends in a water bath containing 5% by weight of NaCl for a minimum of 30 minutes after which time the insulation resistance shall be measured between the salt solution and the test leads. The test potential shall be 500 volts D.C. The readings shall be taken after an electrification time of one minute. 4.3.4 Dielectric Withstanding Voltage: The specimen shall be immersed to within 3 inches of the lead ends in a water bath containing 5% by weight of NaCl for a minimum of 30 minutes after which time the potential between the salt water and the test leads shall be raised from 0 to the specified voltage at a rate of 500 volts per second. This potential shall be maintained for one minute and the voltage reduced to 0. 4.3.5 Temperature Cycling: Fifteen assemblies shall be subjected to 200 cycles. Each cycle shall consist of 20 minutes at 135 °C (275°F) and 5 minutes at 240°C (400°F) in mechanical-convection ovens with an air velocity of 100 to 200 feet per minute past the specimens. The specimens shall be subjected to 20 cycles per day and shall be maintained at 25 ± 5°C (77 ± 9°F) between test days. After the last cycle, the specimen shall be cooled to 25 ± 5°C (77 ± 9°F) within one hour and tested for insulation resistance (4.4.3) and dielectric withstanding voltage (4.4.4). |
类似零件编号 - D-300-08CS1108 |
|
类似说明 - D-300-08CS1108 |
|
|
链接网址 |
隐私政策 |
ALLDATASHEETCN.COM |
ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |