 |
数据搜索系统，热门电子元器件搜索 |
|
|
数据搜索系统，热门电子元器件搜索 |
|
LTC1041 数据表(PDF) 7 Page - Linear Technology |
|
||||||||||||||||||||||||||||||
LTC1041 数据表(HTML) 7 Page - Linear Technology |
|
|
7 / 22 page  LTC3108 7 3108fb VAUX (Pin 1/Pin 2): Output of the Internal Rectifier Cir- cuit and VCC for the IC. Bypass VAUX with at least 1μF of capacitance. An active shunt regulator clamps VAUX to 5.25V (typical). VSTORE (Pin 2/Pin 3): Output for the Storage Capacitor or Battery. A large capacitor may be connected from this pin to GND for powering the system in the event the input voltage is lost. It will be charged up to the maximum VAUX clamp voltage. If not used, this pin should be left open or tied to VAUX. VOUT (Pin 3/Pin 4): Main Output of the Converter. The voltage at this pin is regulated to the voltage selected by VS1 and VS2 (see Table 1). Connect this pin to an energy storage capacitor or to a rechargeable battery. VOUT2 (Pin 4/Pin 5): Switched Output of the Converter. Connect this pin to a switched load. This output is open until VOUT2_EN is driven high, then it is connected to VOUT through a 1.3Ω P-channel switch. If not used, this pin should be left open or tied to VOUT. The peak current in this output is limited to 0.3A typical. VLDO (Pin 5/Pin 6): Output of the 2.2V LDO. Connect a 2.2μF or larger ceramic capacitor from this pin to GND. If not used, this pin should be tied to VAUX. PGD (Pin 6/Pin 7): Power Good Output. When VOUT is within 7.5% of its programmed value, PGD will be pulled up to VLDO through a 1MΩ resistor. If VOUT drops 9% below its programmed value PGD will go low. This pin can sink up to 100μA. VS2 (Pin 7/Pin 10): VOUT Select Pin 2. Connect this pin to ground or VAUX to program the output voltage (see Table 1). VS1 (Pin 8/Pin 11): VOUT Select Pin 1. Connect this pin to ground or VAUX to program the output voltage (see Table 1). VOUT2_EN (Pin 9/Pin 12): Enable Input for VOUT2. VOUT2 will be enabled when this pin is driven high. There is an internal 5M pull-down resistor on this pin. If not used, this pin can be left open or grounded. C1 (Pin 10/Pin 13): Input to the Charge Pump and Rectifier Circuit. Connect a capacitor from this pin to the secondary winding of the step-up transformer. C2 (Pin 11/Pin 14): Input to the N-Channel Gate Drive Circuit. Connect a capacitor from this pin to the secondary winding of the step-up transformer. SW (Pin 12/Pin 15): Drain of the Internal N-Channel Switch. Connect this pin to the primary winding of the transformer. GND (Pins 1, 8, 9, 16) SSOP Only: Ground GND (Exposed Pad Pin 13) DFN Only: Ground. The DFN exposed pad must be soldered to the PCB ground plane. It serves as the ground connection, and as a means of conducting heat away from the die. Table 1. Regulated Voltage Using Pins VS1 and VS2 VS2 VS1 VOUT GND GND 2.35V GND VAUX 3.3V VAUX GND 4.1V VAUX VAUX 5V PIN FUNCTIONS (DFN/SSOP) |
类似零件编号 - LTC1041 |
|
类似说明 - LTC1041 |
|
|
|
链接网址 |
| 隐私政策 |
| ALLDATASHEETCN.COM |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Chinese ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
