数据搜索系统,热门电子元器件搜索 |
|
LB1845 数据表(PDF) 6 Page - Sanyo Semicon Device |
|
LB1845 数据表(HTML) 6 Page - Sanyo Semicon Device |
6 / 9 page LB1845 No.5505-6/9 Usage Notes 1. External diode Since this IC adopts a system based on lower side transistor switching drive, an external diode for the regenerative current that occurs during switching is required between VBB and VOUT. Use a Schottky barrier diode with a low feedthrough current. 2. Noise filters Since spike noise (see Figure 1) occurs when switching to the on state due to the external diode’s feedthrough current, applications must remove noise from the SENSE pin with a noise filter (Cc, Rc) between the E pin and the SENSE pin. However, note that if the values of Cc and Rc are too large, the SENSE voltage rise will be slowed, and the current setting will be shifted towards a higher current level. 3. VREF pin It is possible to change the output current continuously by continuously changing the VREF pin voltage. However, this voltage cannot be set to 0V. The VREF pin input impedance is 26kΩ (±30%) when VREF is 5V. Since this pin is used to set the output current, applications must be designed so that noise does not appear on this pin's input. 4. GND pin Since this IC switches large currents, care must be taken to avoid ground loops when the IC is mounted in the application. The section of the PCB that handles large currents should be designed with a low-impedance pattern, and must be separated from the small signal sections of the circuit. In particular, the ground for the sense resistor Re must be as close as possible to the IC ground. 5. Operation in hold mode There are cases where a current somewhat larger than the current setting may flow in hold mode (light load mode). Since this IC adopts a lower side switching, lower side sense system, the emitter voltage falls and the sense voltage goes to 0 when the switching state goes to off. The circuit then always turns the output on after the toff period has elapsed. At this time, due to the light load, the existence of the time td, and the fact that the output goes on even if the output current is higher than the set current, the output current will be somewhat higher than the set current. Applications should set the current setting somewhat lower than required if this occurs. 6. Function for preventing the upper and lower outputs being on at the same time This IC incorporates a built-in circuit that prevents the through currents that occur when the phase is switched. The table lists the output on and off delay times when PHASE and EANBLE are switched. Sink side Source side On delay time 10 µs 9 µs When PHASE is switched Off delay time 1.5 µs 3 µs On delay time 9 µs 9 µs When ENABLE is on Off delay time 1.5 µs 6.5 µs 7. 1-2 phase excitation and the double 1-2 phase excitation control sequence To reduce the vibration that occurs when the motor turns, this IC supports 1-2 phase excitation and double 1-2 phase excitation by using the output current setting digital input pins I0 and I1 without changing the VREF pin voltage. Tables 1 and 2 list that control sequence, and Figure 2 and Figure 3 present the composite vector diagram for this sequence.2. Noise filters |
类似零件编号 - LB1845 |
|
类似说明 - LB1845 |
|
|
链接网址 |
隐私政策 |
ALLDATASHEETCN.COM |
ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |