数据搜索系统,热门电子元器件搜索 |
|
ISL54222AIUZ-T 数据表(PDF) 9 Page - Intersil Corporation |
|
ISL54222AIUZ-T 数据表(HTML) 9 Page - Intersil Corporation |
9 / 19 page 9 FN6902.1 February 4, 2010 Application Block Diagram Detailed Description The ISL54222A device is a dual single pole/double throw (SPDT) analog switch configured as a DPDT that operates from a single DC power supply in the range of 1.8V to 3.3V. It was designed to function as a dual 2-to-1 multiplexer to select between two USB high-speed differential data signals in portable battery powered products. It is offered in MSOP, TDFN and small µTQFN packages for use in MP3 players, cameras, PDAs, cell phones, and other personal media players. The part consists of four 4.4Ω high-speed (HSx) switches. These switches have high bandwidth and low capacitance to pass USB high-speed (480Mbps) differential data signals with minimal edge and phase distortion. They can also swing from 0V to 3.3V to pass USB full speed (12Mbps) differential data signals with minimal distortion. The device has an enable pin to open all switches and put the part in a low power down state. It can be used to facilitate proper bus disconnect and connection when switching between the USB sources. The ISL54222A was designed for MP3 players, cameras, cell phones, and other personal media player applications that have multiple high-speed or full-speed transceivers sections and need to multiplex between these USB sources to a single USB host (computer). A typical application block diagram of this functionality is shown on page 9. A detailed description of the HS switches is provided in the following section. High-Speed (HSx) Switches The HSx switches (HSD1-, HSD1+, HSD2-, HSD2+) are bi-directional switches that can pass 0V to 3.3V signals. When powered with a 1.8V supply, these switches have a nominal rON of 5.7Ω over the signal range of 0V to 400mV with a rON flatness of 0.60Ω. The rON matching between the HSD1 and HSD2 switches over this signal range is only 0.072Ω, ensuring minimal impact by the switches to USB high-speed signal transitions. As the signal level increases, the rON switch resistance increases. With supply of 1.8V, the switch resistance with the signal level at the rail is nominally 12Ω. See Figures 7, 8, 9, 10, 11 and 12 in the “Typical Performance Curves” beginning on page 11. The HSx switches were specifically designed to pass USB 2.0 high-speed (480Mbps) differential signals in the range of 0V to 400mV. They have low capacitance (4.2pF) and high bandwidth to pass the USB high-speed signals with minimum edge and phase distortion to meet USB 2.0 high-speed signal quality specifications. See Figure 13 in the “Typical Performance Curves” on page 12 for USB High-speed Eye Pattern taken with switches in the differential signal paths. The HSx switches can also pass USB full-speed signals (12Mbps) with minimal distortion and meet all the USB requirements for USB 2.0 full-speed signaling. See Figures 14 and 15 in the “Typical Performance Curves” on page 13 for USB Full-speed Eye Patterns taken with switches in the differential signal paths. The maximum normal operating signal range for the HSx switches is from 0V to 3.3V. The signal voltage should not be allowed to exceed 3.3V or go below ground by more than -0.3V for normal operation. However, in the event that the USB 5.25V VBUS voltage gets shorted to one or both of the D-/D+ pins, the ISL54222A has special fault protection circuitry to prevent damage to the ISL54222A part. The fault circuitry allows the signal pins (D-, D+, HSD1-, HSD1+, HSD2-, HSD2+) to be driven up to 5.5V while the VDD supply voltage is in the range of 0V to 3.3V. In this condition, the part draws < 300µA of IDD current and causes no stress to the IC. In addition, when VDD is at 0V (ground) all switches are OFF and the fault voltage is isolated from the other side of the switch. When VDD is PORTABLE MEDIA DEVICE ISL54222A USB TRANSCEIVER HIGH-SPEED D- D+ SEL GND HSD1- HSD1+ HSD2- HSD2+ VDD OE LOGIC CIRCUITRY µCONTROLLER USB TRANSCEIVER FULL-SPEED VBUS D- D+ GND OR FULL-SPEED HIGH_SPEED OR #1 #2 ISL54222A |
类似零件编号 - ISL54222AIUZ-T |
|
类似说明 - ISL54222AIUZ-T |
|
|
链接网址 |
隐私政策 |
ALLDATASHEETCN.COM |
ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |