数据搜索系统,热门电子元器件搜索 |
|
DB16S522D 数据表(PDF) 13 Page - Sanyo Semicon Device |
|
DB16S522D 数据表(HTML) 13 Page - Sanyo Semicon Device |
13 / 68 page 12 ■ Rotary switch(RSW) and the mode change switch(PSW) When it selects the step angle, the driving current is selected, and stops the current is selected, set by combining rotary switch (RSW) and mode change switch (PSW). 1. Step angle select(S.S) The divisions of the basic step angle (0.9 °/step) when micro step driving can be set. Gradation 0 1234567 Partition 1 2 2.5 4 5 8 10 20 Gradation 8 9 A B C D E F Partition 25 40 50 80 100 125 200 250 Ex-factory setting is at 1 (division 2) *The step angle select switch (S.S) and the number of partitions become invalid by EXT input signal ON (built-in photo coupler ON) of Input/Output signal connector (CN2). 2. Driving current select(RUN) The Motor operation current value can be selected. Gradation 0 1234567 Motor current (%) 100 (rated) 95 90 85 80 75 70 65 Gradation 8 9 A B C D E F Motor current (%) ) 60 55 50 45 40 35 30 25 Ex-factory setting is at 0 (rated value). *When there is a sufficient extra motor torque, lowering the operation current value will be effective in the lower vibration. The Motor output torque is almost proportional to the current value. When adjusting the operational torque, confirm the sufficient operation margin and determine the Motor current value. 3. Current Select when Stop (STP) The motor current value when stop and when power down input signal ON (power low function is selected by dip switch) can be selected. Gradation 0 1234567 Motor current (%) 100 (rated) 95 90 85 80 75 70 65 Gradation 8 9 A B C D E F Motor current (%) 60 55 50 45 40 35 30 25 Ex-factory setting is set at A (50%). *The current setting when stop by STP becomes valid when the Motor stops (approximately 200ms after the last pulse input) and when power down input signal ◎ For pulse stream I/F mode ◎ For parallel I/F mode and serial I/F mode The slave bureau address of serial communications can be set. RSW Slave station address (HEX) 00 1 1 :: EE FF Ex-factory setting is set at 0 *The slave station address of the pulse stream I/F mode is fixed at 0. |
类似零件编号 - DB16S522D |
|
类似说明 - DB16S522D |
|
|
链接网址 |
隐私政策 |
ALLDATASHEETCN.COM |
ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |