数据搜索系统,热门电子元器件搜索
  Chinese  ▼

Delete All
ON OFF
ALLDATASHEETCN.COM

X  

预览 PDF Download HTML

HY5PS121621CFP-S6I 数据表(PDF) 27 Page - Hynix Semiconductor

部件名 HY5PS121621CFP-S6I
功能描述  512Mb DDR2 SDRAM
Download  38 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
制造商  HYNIX [Hynix Semiconductor]
网页  http://www.skhynix.com/kor/main.do
标志 HYNIX - Hynix Semiconductor

HY5PS121621CFP-S6I 数据表(HTML) 27 Page - Hynix Semiconductor

Back Button HY5PS121621CFP-S6I Datasheet HTML 23Page - Hynix Semiconductor HY5PS121621CFP-S6I Datasheet HTML 24Page - Hynix Semiconductor HY5PS121621CFP-S6I Datasheet HTML 25Page - Hynix Semiconductor HY5PS121621CFP-S6I Datasheet HTML 26Page - Hynix Semiconductor HY5PS121621CFP-S6I Datasheet HTML 27Page - Hynix Semiconductor HY5PS121621CFP-S6I Datasheet HTML 28Page - Hynix Semiconductor HY5PS121621CFP-S6I Datasheet HTML 29Page - Hynix Semiconductor HY5PS121621CFP-S6I Datasheet HTML 30Page - Hynix Semiconductor HY5PS121621CFP-S6I Datasheet HTML 31Page - Hynix Semiconductor Next Button
Zoom Inzoom in Zoom Outzoom out
 27 / 38 page
background image
Rev. 0.8 / Oct. 2007
27
1HY5PS12421C(L)FP-xI
1HY5PS12821C(L)FP-xI
1HY5PS121621C(L)FP-xI
Specific Notes for dedicated AC parameters
1. User can choose which active power down exit timing to use via MRS(bit 12). tXARD is expected to be used for fast
active power down exit timing. tXARDS is expected to be used for slow active power down exit timing where a lower
power value is defined by each vendor data sheet.
2. AL = Additive Latency
3. This is a minimum requirement. Minimum read to precharge timing is AL + BL/2 providing the tRTP and tRAS(min)
have been satisfied.
4. A minimum of two clocks (2 * tCK) is required irrespective of operating frequency
5. Timings are guaranteed with command/address input slew rate of 1.0 V/ns. See System Derating for other slew rate
values.
6. Timings are guaranteed with data, mask, and (DQS/RDQS in singled ended mode) input slew rate of 1.0 V/ns.
See System Derating for other slew rate values.
7. Timings are guaranteed with CK/CK differential slew rate of 2.0 V/ns. Timings are guaranteed for DQS signals with a
differen tial slew rate of 2.0 V/ns in differential strobe mode and a slew rate of 1V/ns in single ended mode. See System
Derating for other slew rate values.
8. tDS and tDH derating table (for DDR2- 400 / 533)
1) For all input signals the total tDS(setup time) and tDH(hold time) required is calculated by adding the datasheet value
to the derating value listed in above Table.
Setup(tDS) nominal slew rate for a rising signal is defined as the slew rate between the last crossing of VREF(dc) and the
first crossing of Vih(ac)min. Setup(tDS) nominal slew rate for a falling signal is defined as the slew rate between the last
crossing of VREF(dc) and the first crossing of Vil(ac)max. If the actual signal is always earlier than the nominal slew rate
line between shaded ‘ VREF(dc) to ac region’, use nominal slew rate for derating value(see Fig a.) If the actual signal is
later than the nominal slew rate line anywhere between shaded ‘VREF(dc) to ac region’, the slew rate of a tangent line to
the actual signal from the ac level to dc level is used for derating value(see Fig b.)
Hold(tDH) nominal slew rate for a rising signal is defined as the slew rate rate between the last crossing of Vil(dc) max and
the first crossing of VREF(dc). Hold (tDH) nominal slew rate for a falling signal is defined as the slew rate between the last
crossing of Vih(dc) min and the first crossing of VREF(dc). If the actual signal is earlier than the nominal slew rate line
anywhere between shaded ‘dc to VREF(dc) region’, the slew rate of a tangent line to the actual signal from the dc level to
VREF(dc) level is used for derating value(see Fig d.)
△ tD
S
△ tD
H
△ tD
S
△ tD
H
△ tD
S
△ tD
H
△ tD
S
△ tD
H
△ tD
S
△ tD
H
△ tD
S
△ tD
H
△ tD
S
△ tD
H
△ tD
S
△ tD
H
△ tD
S
△ tD
H
2.0
125
45
125
45
+125 +45
-
--
--
---
--
--
1.5
83
21
83
21
+83
+21
95
33
-
-
-
-
-
-
-
-
-
-
1.0
0
0
0
0
0
0
12
12
24
24
-
---
--
--
0.9
-
-
-11
-14
-11
-14
1
-2
13
10
25
22
-
-
-
-
-
-
0.8
-
-
-
-
-25
-31
-13
-19
-1
-7
11
5
23
17
-
-
-
-
0.7
--
---
-
-31
-42
-42
-19
-7
-8
5
-6
17
6
--
0.6
-
-
-
-
-
-
-
-
-43
-59
-31
-47
-19
-35
-7
-23
5
-11
0.5
--
---
--
--
-
-74
-89
-62
-77
-50
-65
-38
-53
0.4
--
---
--
--
--
-
-127 -140 -115 -128 -103 -116
tDS, tDH Derating Values(ALL units in 'ps', Note 1 applies to entire Table)
1.6 V/ns
1.4 V/ns
1.2 V/ns
1.0 V/ns
4.0 V/ns
3.0 V/ns
0.8 V/ns
DQ
Slew
rate
V/ns
DQS, DQS Differential Slew Rate
2.0 V/ns
1.8 V/ns


Html Pages

1  2  3  4  5  6  7  8  9  10  11  12  13  14  15  16  17  18  19  20  21  22  23  24  25  26  27  28  29  30  31  32  33  34  35  36  37  38 


数据表 下载

Go To PDF Page


链接网址




隐私政策
ALLDATASHEETCN.COM
ALLDATASHEET是否为您带来帮助?  [ DONATE ] 

关于 Alldatasheet   |   广告服务   |   联系我们   |   隐私政策   |   链接交换   |   制造商名单
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn