数据搜索系统,热门电子元器件搜索 |
|
AD5174BCPZ-10-RL7 数据表(PDF) 4 Page - Analog Devices |
|
AD5174BCPZ-10-RL7 数据表(HTML) 4 Page - Analog Devices |
4 / 20 page AD5174 Rev. 0 | Page 4 of 20 Parameter Symbol Test Conditions/Comments Min Typ1 Max Unit DYNAMIC CHARACTERISTICS4, 10 Bandwidth −3 dB, RAW = 5 kΩ, Terminal W, see Figure 24 700 kHz Total Harmonic Distortion VA = 1 V rms, f = 1 kHz, RAW = 5 kΩ −90 dB Resistor Noise Density RWB = 5 kΩ, TA = 25°C, f = 10 kHz 13 nV/√Hz 1 Typical specifications represent average readings at 25°C, VDD = 5 V, and VSS = 0 V. 2 Resistor position nonlinearity error (R-INL) is the deviation from an ideal value measured between the maximum resistance and the minimum resistance wiper positions. R-DNL measures the relative step change from the ideal between successive tap positions. 3 The maximum current in each code is defined by IAW = (VDD − 1)/RAW. 4 Guaranteed by design and not subject to production test. 5 See Figure 9 for more details. 6 Resistor Terminal A and Resistor Terminal W have no limitations on polarity with respect to each other. Dual-supply operation enables ground referenced bipolar signal adjustment. 7 Different from operating current; the supply current for the fuse program lasts approximately 55 ms. 8 Different from operating current; the supply current for the fuse read lasts approximately 500 ns. 9 PDISS is calculated from (IDD × VDD) + (ISS × VSS). 10 All dynamic characteristics use VDD = +2.5 V, VSS = −2.5 V. INTERFACE TIMING SPECIFICATIONS VDD = 2.7 V to 5.5 V, VSS = 0 V; VDD = 2.5 V, VSS = −2.5 V; all specifications TMIN to TMAX, unless otherwise noted. Table 2. Parameter Limit1 Unit Test Conditions/Comments t12 20 ns min SCLK cycle time t2 10 ns min SCLK high time t3 10 ns min SCLK low time t4 15 ns min SYNC to SCLK falling edge setup time t5 5 ns min Data setup time t6 5 ns min Data hold time t7 1 ns min SCLK falling edge to SYNC rising edge t83 400 ns min Minimum SYNC high time t9 15 ns min SYNC rising edge to next SCLK fall ignored t104 450 ns max SCLK rising edge to SDO valid tMEMORY_READ 6 μs max Memory readback execute time tMEMORY_PROGRAM 350 ms max Memory program time tRESET 600 μs max Reset OTP restore time tPOWER-UP5 2 ms max Power-on 50-TP restore time 1 All input signals are specified with tr = tf = 1 ns/V (10% to 90% of VDD) and timed from a voltage level of (VIL + VIH)/2. 2 Maximum SCLK frequency is 50 MHz. 3 Refer to t MEMORY_READ and tMEMORY_PROGRAM for memory commands operations. 4 RPULL_UP = 2.2 kΩ to VDD with a capacitance load of 168 pF. 5 Maximum time after VDD − VSS is equal to 2.5 V. |
类似零件编号 - AD5174BCPZ-10-RL7 |
|
类似说明 - AD5174BCPZ-10-RL7 |
|
|
链接网址 |
隐私政策 |
ALLDATASHEETCN.COM |
ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |