数据搜索系统,热门电子元器件搜索 |
|
MAX7490CEE+ 数据表(PDF) 9 Page - Maxim Integrated Products |
|
MAX7490CEE+ 数据表(HTML) 9 Page - Maxim Integrated Products |
9 / 18 page Dual Universal Switched-Capacitor Filters _______________________________________________________________________________________ 9 2nd-Order Filter Stage The MAX7490/MAX7491 are dual biquad filters. The biquad topology allows the use of standard filter tables and equations to implement simultaneous lowpass, bandpass, and notch or highpass filters. Topologies such as Butterworth, Chebyshev, Bessel, elliptic, as well as custom algorithms are possible. Internal Common Voltage The COM pin sets the common-mode input voltage and is internally biased to VDD/2 with a resistor-divider. The resistors used are typically 250kΩ for the MAX7490, and typically 80kΩ for the MAX7491. The common- mode voltage is easily overdriven by an external volt- age supply if desired. Bypass COM to the analog ground with at least a 0.1µF capacitor. Inverting Inputs Locate resistors that are connected to INV_ as close as possible to INV_ to reduce stray capacitance and noise pickup. INV_ are inverting inputs to continuous-time op amps, and behave like a virtual ground. There is no sampling energy present on these inputs. Outputs Each switched-capacitor section, together with two to four external resistors, can generate all standard 2nd- order functions: bandpass, lowpass, highpass, and notch (band-reject) functions. Three of these functions are simultaneously available. The maximum signal swing is limited by the power-supply voltages used. The amplifiers’ outputs in the MAX7490/MAX7491 are able to swing to within approximately 0.2V of either supply. Driving coaxial cable, large capacitive loads, or total resistive loads less than 10kΩ will degrade the total harmonic distortion (THD) performance. Note that the effective resistive load at the output must include both the feedback resistors and any external load resistors. Low-Power Shutdown Mode The MAX7490/MAX7491 have a shutdown mode that is activated by driving SHDN low. In shutdown mode, the filter supply current reduces to < 1µA (max), and the fil- ter outputs become high impedance. The COM input also becomes high impedance during shutdown. For normal operation, drive SHDN high or connect to VDD. __________Applications Information Designing with the MAX7490/MAX7491 begins by selecting the mode that best fits the desired circuit requirements. Table 1 lists the available modes and their relative advantages and disadvantages. Table 2 lists the different nomenclature used in the explanations that follow. Σ ∫ ∫ NA/HPA (3) SHDN VDD (8) GND (7) CLK (9) EXTCLK (10) INVB (13) COM (11) R R INVA (4) (6) SA (5) BPA (2) LPA (1) + - Σ ∫ ∫ NB/HPB (14) SB (12) BPB (15) LPB (16) + - Figure 1. Block Diagram |
类似零件编号 - MAX7490CEE+ |
|
类似说明 - MAX7490CEE+ |
|
|
链接网址 |
隐私政策 |
ALLDATASHEETCN.COM |
ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |