数据搜索系统,热门电子元器件搜索 |
|
SMDP-672061HV-15SCC 数据表(PDF) 4 Page - ATMEL Corporation |
|
SMDP-672061HV-15SCC 数据表(HTML) 4 Page - ATMEL Corporation |
4 / 20 page 4 M672061H 4144K-AERO-04/07 Figure 2. Reset (write (read) to Programmable Half Full Flag register) Write Enable (W) A write cycle is initiated on the falling edge of this input if the Full Flag (FF) is not set. Data set-up and hold times must be maintained in the rise time of the leading edge of the Write Enable (W). Data is stored sequentially in the Ram array, regardless of any current read operation. Once half the memory is filled, and during the falling edge of the next write operation, the Half-Full Flag (HF) will be set to low and remain in this state until the difference between the write and read pointers is less than or equal to half of the total available memory in the device. The Half-Full Flag (HF) is then reset by the rising edge of the read operation. To prevent data overflow, the Full Flag (FF) will go low, inhibiting further write opera- tions. On completion of a valid read operation, the Full Flag (FF) will go high after TRFF, allowing a valid write to begin. When the FIFO stack is full, the internal write pointer is blocked from W, so that external changes to W will have no effect on the full FIFO stack. Read Enable (R) A read cycle is initiated on the falling edge of the Read Enable (R) provided that the Empty Flag (EF) is not set. The data is accessed on a first in/first out basis, not including any current write operations. After Read Enable (R) goes high, the Data Outputs (Q0 - Q8) will return to a high impedance state until the next Read operation. When all the data in the FIFO stack has been read, the Empty Flag (EF) will go low, allowing the “final” read cycle, but inhibiting further read operations while the data outputs remain in a high impedance state. Once a valid write operation has been completed, the Empty Flag (EF) will go high after tWEF and a valid read may then be initiated. When the FIFO stack is empty, the internal read pointer is blocked from R, so that external changes to R will have no effect on the empty FIFO stack. First Load/Retransmit (FL/RT) This is a dual-purpose input. In the Depth Expansion Mode, this pin is connected to ground to indicate that it is the first loaded (see Operating Modes). In the Single Device Mode, this pin acts as the retransmit input. The Single Device Mode is initiated by con- necting the Expansion In (XI) to ground. The M672061H can be set to retransmit data when the Retransmit Enable Control (RT) input is pulsed low. A retransmit operation will set the internal read point to the first loca- tion and will not affect the write pointer. Read Enable (R) and Write Enable (W) must be in the high state during retransmit. The retransmit feature is intended for use when a number of writes are equal to or less than the depth of the FIFO has occured since the last RS cycle. The retransmit feature is not compatible with the Depth Expansion Mode and will affect the Half-Full Flag (HF), in accordance with the relative locations of the read and write pointers. |
类似零件编号 - SMDP-672061HV-15SCC |
|
类似说明 - SMDP-672061HV-15SCC |
|
|
链接网址 |
隐私政策 |
ALLDATASHEETCN.COM |
ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |