 |
数据搜索系统，热门电子元器件搜索 |
|
|
数据搜索系统，热门电子元器件搜索 |
|
STK14C88-3WF45I 数据表(PDF) 11 Page - Simtek Corporation |
|
||||||||||||||||||||||||||||||
STK14C88-3WF45I 数据表(HTML) 11 Page - Simtek Corporation |
|
|
11 / 18 page  11 STK14C88-3 Feb, 2008 Document Control #ML0015 Rev 2.0 SOFTWARE NONVOLATILE RECALL A software RECALL cycle is initiated with a sequence of READ operations in a manner similar to the soft- ware STORE initiation. To initiate the RECALL cycle, the following sequence of E controlled READ opera- tions must be performed: 1. Read address 0E38 (hex) Valid READ 2. Read address 31C7 (hex) Valid READ 3. Read address 03E0 (hex) Valid READ 4. Read address 3C1F (hex) Valid READ 5. Read address 303F (hex) Valid READ 6. Read address 0C63 (hex) Initiate RECALL cycle Internally, RECALL is a two-step procedure. First, the SRAM data is cleared, and second, the nonvolatile information is transferred into the SRAM cells. After the t RECALL cycle time the SRAM will once again be ready for READ and WRITE operations. The RECALL operation in no way alters the data in the nonvolatile elements. The nonvolatile data can be recalled an unlimited number of times. AutoStore MODE The STK14C88-3 can be powered in one of three modes. During normal AutoStore operation, the STK14C88- 3 will draw current from V CC to charge a capacitor connected to the V CAP pin. This stored charge will be used by the chip to perform a single STORE opera- tion. After power up, when the voltage on the V CAP pin drops below V SWITCH, the part will automatically disconnect the V CAP pin from V CC and initiate a STORE operation. Figure 2 shows the proper connection of capacitors for automatic store operation. A charge storage capacitor having a capacity of between 68 μF and 220 μF (± 20%) rated at 4.7V should be provided. In order to prevent unneeded STORE operations, automatic STOREs as well as those initiated by externally driving HSB low will be ignored unless at least one WRITE operation has taken place since the most recent STORE or RECALL cycle. Software- initiated STORE cycles are performed regardless of whether a WRITE operation has taken place. If the power supply drops faster than 20 μs/volt before V CC reaches VSWITCH, then a 1 ohm resistor should be inserted between V CC and the system sup- ply to avoid momentary excess of current between Vcc and Vcap. AutoStore INHIBIT MODE If an automatic STORE on power loss is not required, then Vcc can be tied to ground and system power applied to VCAP (Figure 3). This is the AutoStore Inhibit mode, in which the AutoStore func- tion is disabled. If the STK14C88-3 is operated in this configuration, references to Vcc should be changed to VCAP throughout this data sheet. In this mode, STORE operations may be triggered through software control. It is not permissible to change between these three options “on the fly.” Figure 3: AutoStore Inhibit Mode *If HSB is not used, it should be left unconnected. 17 1 16 32 31 30 Figure 2: AutoStore Mode *If HSB is not used, it should be left unconnected. 10kO* + 1 16 17 32 31 30 |
类似零件编号 - STK14C88-3WF45I |
|
类似说明 - STK14C88-3WF45I |
|
|
|
链接网址 |
| 隐私政策 |
| ALLDATASHEETCN.COM |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Chinese ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
