数据搜索系统,热门电子元器件搜索 |
|
LM2700MT-ADJ 数据表(PDF) 10 Page - National Semiconductor (TI) |
|
|
LM2700MT-ADJ 数据表(HTML) 10 Page - National Semiconductor (TI) |
10 / 17 page Operation (Continued) very little load changes, and at lower current outputs, the input capacitor size can often be reduced. The size can also be reduced if the input of the regulator is very close to the source output. The size will generally need to be larger for applications where the regulator is supplying nearly the maximum rated output or if large load steps are expected. A minimum value of 10µF should be used for the less stressful condtions while a 33µF or 47µF capacitor may be required for higher power and dynamic loads. Larger values and/or lower ESR may be needed if the application requires very low ripple on the input source voltage. The choice of output capacitors is also somewhat arbitrary and depends on the design requirements for output voltage ripple. It is recommended that low ESR (Equivalent Series Resistance, denoted R ESR) capacitors be used such as ceramic, polymer electrolytic, or low ESR tantalum. Higher ESR capacitors may be used but will require more compen- sation which will be explained later on in the section. The ESR is also important because it determines the peak to peak output voltage ripple according to the approximate equation: ∆V OUT ) 2 ∆i LRESR (in Volts) A minimum value of 10µF is recommended and may be increased to a larger value. After choosing the output capaci- tor you can determine a pole-zero pair introduced into the control loop by the following equations: Where R L is the minimum load resistance corresponding to the maximum load current. The zero created by the ESR of the output capacitor is generally very high frequency if the ESR is small. If low ESR capacitors are used it can be neglected. If higher ESR capacitors are used see the High Output Capacitor ESR Compensation section. RIGHT HALF PLANE ZERO A current mode control boost regulator has an inherent right half plane zero (RHP zero). This zero has the effect of a zero in the gain plot, causing an imposed +20dB/decade on the rolloff, but has the effect of a pole in the phase, subtracting another 90˚ in the phase plot. This can cause undesirable effects if the control loop is influenced by this zero. To ensure the RHP zero does not cause instability issues, the control loop should be designed to have a bandwidth of less than 1⁄2 the frequency of the RHP zero. This zero occurs at a fre- quency of: where I LOAD is the maximum load current. SELECTING THE COMPENSATION COMPONENTS The first step in selecting the compensation components R C and C C is to set a dominant low frequency pole in the control loop. Simply choose values for R C and CC within the ranges given in the Introduction to Compensation section to set this pole in the area of 10Hz to 500Hz. The frequency of the pole created is determined by the equation: where R O is the output impedance of the error amplifier, approximately 850k Ω. Since R C is generally much less than R O, it does not have much effect on the above equation and can be neglected until a value is chosen to set the zero f ZC. f ZC is created to cancel out the pole created by the output capacitor, f P1. The output capacitor pole will shift with differ- ent load currents as shown by the equation, so setting the zero is not exact. Determine the range of f P1 over the ex- pected loads and then set the zero f ZC to a point approxi- mately in the middle. The frequency of this zero is deter- mined by: Now R C can be chosen with the selected value for CC. Check to make sure that the pole f PC is still in the 10Hz to 500Hz range, change each value slightly if needed to ensure both component values are in the recommended range. After checking the design at the end of this section, these values can be changed a little more to optimize performance if desired. This is best done in the lab on a bench, checking the load step response with different values until the ringing and overshoot on the output voltage at the edge of the load steps is minimal. This should produce a stable, high performance circuit. For improved transient response, higher values of R C should be chosen. This will improve the overall bandwidth which makes the regulator respond more quickly to tran- sients. If more detail is required, or the most optimal perfor- mance is desired, refer to a more in depth discussion of compensating current mode DC/DC switching regulators. HIGH OUTPUT CAPACITOR ESR COMPENSATION When using an output capacitor with a high ESR value, or just to improve the overall phase margin of the control loop, another pole may be introduced to cancel the zero created by the ESR. This is accomplished by adding another capaci- tor, C C2, directly from the compensation pin VC to ground, in parallel with the series combination of R C and CC. The pole should be placed at the same frequency as f Z1, the ESR zero. The equation for this pole follows: To ensure this equation is valid, and that C C2 can be used without negatively impacting the effects of R C and CC,fPC2 must be greater than 10f ZC. CHECKING THE DESIGN The final step is to check the design. This is to ensure a bandwidth of 1⁄2 or less of the frequency of the RHP zero. This is done by calculating the open-loop DC gain, A DC. After this value is known, you can calculate the crossover visually by placing a −20dB/decade slope at each pole, and a +20dB/ decade slope for each zero. The point at which the gain plot crosses unity gain, or 0dB, is the crossover frequency. If the crossover frequency is less than 1⁄2 the RHP zero, the phase margin should be high enough for stability. The phase mar- www.national.com 10 |
类似零件编号 - LM2700MT-ADJ |
|
类似说明 - LM2700MT-ADJ |
|
|
链接网址 |
隐私政策 |
ALLDATASHEETCN.COM |
ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |