数据搜索系统,热门电子元器件搜索 |
|
L6713A 数据表(PDF) 10 Page - Holtek Semiconductor Inc |
|
L6713A 数据表(HTML) 10 Page - Holtek Semiconductor Inc |
10 / 64 page Pin settings L6713A 10/64 40 to 45 VID5 to VID0 Intel Mode. Voltage IDentification Pins (also applies to VID6, VID7). Internally pulled up by 25µA to 5V, connect to SGND to program a '0' or leave floating to program a '1'. They allow programming output voltage as specified in Table 6 and Table 7 according to VID_SEL status. OVP and UVP protection comes as a consequence of the programmed code (See Table 11). AMD Mode. Voltage IDentification Pins. Internally pulled down by 12.5µA, leave floating to program a '0' while pull up to more than 1.4V to program a '1'. They allow programming the output voltage as specified in Table 9 (VID7 doesn’t care). OVP and UVP protection comes as a consequence of the programmed code (See Table 11). Note. VID6 not used, need to be shorted to SGND. 46 SS_END/ PGOOD SSEND - Intel Mode. Soft Start END Signal. Open Drain Output sets free after SS has finished and pulled low when triggering any protection. Pull up to a voltage lower than 5V (typ), if not used it can be left floating. PGOOD - AMD Mode. Open Drain Output set free after SS has finished and pulled low when VSEN is lower than the relative threshold. Pull up to a voltage lower than 5V (typ), if not used it can be left floating. 47 VR_HOT Voltage Regulator HOT. Over Temperature Alarm Signal. Open Drain Output, set free when TM overcomes the Alarm Threshold. Thermal Monitoring Output enabled if Vcc > UVLOVCC. See “Thermal monitor” Section for details and typical connections. 48 VR_FAN Voltage Regulator FAN. Over Temperature Warning Signal. Open Drain Output, set free when TM overcomes the Warning Threshold. Thermal Monitoring Output enabled if Vcc > UVLOVCC. See “Thermal monitor” Section for details and typical connections. 49 TM Thermal Monitor Input. It senses the regulator temperature through apposite network and drives VR_FAN and VR_HOT accordingly.Short TM pin to SGND if not used. See “Thermal monitor” Section for details and typical connections. 50 SGND All the internal references are referred to this pin. Connect to the PCB Signal Ground. 51 N.C. Not internally connected. 52 N.C. Not internally connected. 53 N.C. Not internally connected. 54 PGND2 Channel 2 LS Driver return path. Connect to Power ground Plane. It must be connected to Power ground Plane also when using 2-Phase Operation. 55 LGATE2 Channel 2 LS Driver Output.A small series resistor helps in reducing device- dissipated power. Leave floating when using 2 Phase operation. Table 1. Pin description N° Pin Function |
类似零件编号 - L6713A |
|
类似说明 - L6713A |
|
|
链接网址 |
隐私政策 |
ALLDATASHEETCN.COM |
ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |