数据搜索系统,热门电子元器件搜索 |
|
ST6280BQ1 数据表(PDF) 7 Page - STMicroelectronics |
|
ST6280BQ1 数据表(HTML) 7 Page - STMicroelectronics |
7 / 80 page 7/80 ST62T80B/E80B 1.2 PIN DESCRIPTIONS VDD and VSS. Power is supplied to the MCU via these two pins. VDD is the power connection and VSS is the ground connection. OSCin and OSCout. These pins are internally connected to the on-chip oscillator circuit. A quartz crystal, a ceramic resonator or an external clock signal can be connected between these two pins. The OSCin pin is the input pin, the OSCout pin is the output pin. RESET. The active-low RESET pin is used to re- start the microcontroller. TEST/V PP. The TEST must be held at VSS for nor- mal operation. If TEST pin is connected to a +12.5V level during the reset phase, the EPROM/OTP programming Mode is entered. NMI. The NMI pin provides the capability for asyn- chronous interruption, by applying an external non maskable interrupt to the MCU. The NMI input is falling edge sensitive with Schmitt trigger charac- teristics. The user can select as option the availa- bility of an on-chip pull-up at this pin. PA2-PA7. These 6 lines are organised as one I/O port (A). Each line may be configured under soft- ware control as inputs with or without internal pull- up resistors, interrupt generating inputs with pull- up resistors, open-drain or push-pull outputs, PA5/SCL, PA6/Sin and PA7/Sout can be used re- spectively as data clock, data in and clock pins for the on-chip SPI, while PA4/TIMER can be used as Timer I/O. In addition, PA2-PA7 can sink 20mA for direct LED or TRIAC drive. PB0...PB7. These 8 lines are organised as one I/O port (B). Each line may be configured under soft- ware control as inputs with or without internal pull- up resistors, interrupt generating inputs with pull- up resistors, open-drain or push-pull outputs, an- alog inputs for the A/D converter. PB6/ARTIMin and PB7/ARTIMout are either Port B I/O bits or the input and output of the ARTimer. PB1 (resp. PB0) can also be used as reception (resp. transmission) line for the embedded UART. PC0-PC7. These 8 lines are organised as one I/O port (C). Each line may be configured under soft- ware control as input with or without internal pull- up resistor, interrupt generating input with pull-up resistor, open-drain or push-pull output, or analog imputs for the A/D Converter. PC0-PC3 can sink 20mA for direct LED or TRIAC drive, while PC4- PC7 can be used as analog inputs for the A/D Converter. COM1-COM8. These eight pins are the LCD pe- ripheral common outputs. They are the outputs of the on-chip backplane voltage generator which is used for multiplexing the LCD lines. COM9/S1-COM16/S8. These pins are the 8 multi- plexed common/segment lines. Under software selected control, they can act as LCD common outputs allowing a 48 x 16 dot matrix operation, or they can act as segment outputs alowwing 56 x 8 dot matrix operation. S9-S56. These pins are the 48 LCD peripheral segment outputs. VLCD1/5, VLCD5/5. Display supply voltage inputs for determining the display voltage levels on common and segment pins during multiplex oper- ation. OSC32in and OSC32out. These pins are inter- nally connected with the on-chip 32kHz oscillator circuit. A 32.768kHz quartz crystal can be con- nected between these two pins if it is necessary to provide the LCD stand-by clock and real time inter- rupt. OSC32in is the input pin, OSC32out is the output pin. 7 |
类似零件编号 - ST6280BQ1 |
|
类似说明 - ST6280BQ1 |
|
|
链接网址 |
隐私政策 |
ALLDATASHEETCN.COM |
ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |