数据搜索系统,热门电子元器件搜索 |
|
TDA8595TH 数据表(PDF) 8 Page - NXP Semiconductors |
|
TDA8595TH 数据表(HTML) 8 Page - NXP Semiconductors |
8 / 50 page TDA8595_2 © NXP B.V. 2007. All rights reserved. Product data sheet Rev. 02 — 21 November 2007 8 of 50 NXP Semiconductors TDA8595 I2C-bus controlled 4 × 45 W power amplifier 7.6 Speaker protection To prevent damage of the speaker when one side of the speaker is connected to ground, a missing current protection is implemented. When in one channel the current in the high side power is not equal to the current in the low side power, a fault condition is assumed and the channel will be switched off. The speaker protection will be activated under the following conditions: • Vo < 1.75 V and Imissing(det) > 1 A during 80 µs • Vo > 1.75 V and Imissing(det) > 3 A during 80 µs 7.7 Standby and mute operation The function of the STB pin is different in legacy mode and I2C-bus mode. 7.7.1 I2C-bus mode When the STB pin is LOW, the total quiescent current is low, and the I2C-bus lines will not be loaded. When the STB pin is switched HIGH the TDA8595 is put in operating condition and will perform a power-on reset, which results in a LOW-level DIAG pin. The TDA8595 will start up when instruction bit IB1[D0] is set. Bit D0 will also reset the ‘power-on reset occurred’ bit (DB2[D7]) and releases the DIAG pin. The soft mute and soft mute can be activated via the I2C-bus. The soft mute can be activated independently for the front channels (channel 1 and channel 3) and rear channels (channel 2 and channel 4), and mutes the audio in 20 ms. The fast mute activates the mute for all channels at the same time and mutes the audio in 0.1 ms. Releasing the mute after a fast mute will be by a soft un-mute of approximately 20 ms. When the STB pin is switched to Standby mode and the amplifier has started, first the fast mute will be activated and then the amplifier will shut-down. For instance, during an engine start, it is possible to fully mute the amplifiers within 100 µs by switching the STB pin to zero. 7.7.2 Legacy mode (pin ADSEL connected to ground) The function of the STB pin will change from standby/operating to standby/mute/operating and the amplifier will start directly when the STB is put into mute or operating. Mute operating is controlled via an internal timer (20 ms) to minimize mute-on pops. When the STB pin is switched directly from operating to standby, first the fast mute will be activated (switching to mute within 100 µs) and then the amplifier will shut-down. 7.8 Start-up and shut-down sequence To prevent the amplifier producing switch-on or switch-off pop noise, the capacitor on the SVR pin is used for smooth start-up and shut-down. Increasing the value of the SVR capacitor will mean a longer start-up and shut-down time. The amplifier output voltage is charged to half the supply voltage minus 1.4 V in mute condition, independent of the I2C-bus mute settings in I2C-bus mode or pin STB voltage in legacy mode. The last 1.4 V, where the output will reach half the supply voltage, is used to release the mute if the I2C-bus bits (IB2[D2:D0] = 000) were set to mute-off (VSTB > 6.5 V in legacy mode), or will stay in mute when the bits were set to mute (2.6V<VSTB < 4.5 V in legacy mode). |
类似零件编号 - TDA8595TH |
|
类似说明 - TDA8595TH |
|
|
链接网址 |
隐私政策 |
ALLDATASHEETCN.COM |
ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |