数据搜索系统,热门电子元器件搜索 |
|
TC552501EZB713 数据表(PDF) 9 Page - Microchip Technology |
|
TC552501EZB713 数据表(HTML) 9 Page - Microchip Technology |
9 / 18 page © 2005 Microchip Technology Inc. DS21435F-page 9 TC55 3.0 PIN DESCRIPTIONS The descriptions of the pins are listed in Table 3-1. TABLE 3-1: PIN FUNCTION TABLE 3.1 Ground Terminal (GND) Regulator ground. Tie GND to the negative side of the output and the negative side of the input capacitor. Only the LDO bias current (1 µA typical) flows out of this pin, there is no high current. The LDO output regu- lation is referenced to this pin. Minimize voltage drops between this pin and the minus side of the load. 3.2 Regulated Voltage Output (VOUT) Connect VOUT to the positive side of the load and the positive terminal of the output capacitor. The positive side of the output capacitor should be physically located as close to the LDO VOUT pin as is practical. The current flowing out of this pin is equal to the DC load current. 3.3 Unregulated Supply Input (VIN) Connect the input supply voltage and the positive side of the input capacitor to VIN. The input capacitor should be physically located as close as is practical to VIN. The current flow into this pin is equal to the DC load current, plus the LDO bias current (1 µA typical.) 4.0 DETAILED DESCRIPTION The TC55 is a low quiescent current, precision, fixed- output voltage LDO. Unlike bipolar regulators, the TC55 supply current does not increase proportionally with load current. 4.1 Output Capacitor A minimum of 1 µF output capacitor is required. The output capacitor should have an effective series resis- tance (esr) greater than 0.1 Ω and less than 5Ω, plus a resonant frequency above 1 MHz. Larger output capacitors can be used to improve supply noise rejec- tion and transient response. Care should be taken when increasing COUT to ensure that the input imped- ance is not high enough to cause high input impedance oscillation. 4.2 Input Capacitor A 1 µF input capacitor is recommended for most applications when the input impedance is on the order of 10 Ω. Larger input capacitance may be required for stability when operating off of a battery input, or if there is a large distance from the input source to the LDO. When large values of output capacitance are used, the input capacitance should be increased to prevent high source impedance oscillations. Pin No. Symbol Description 1 GND Ground Terminal 2VOUT Regulated Voltage Output 3VIN Unregulated Supply Input |
类似零件编号 - TC552501EZB713 |
|
类似说明 - TC552501EZB713 |
|
|
链接网址 |
隐私政策 |
ALLDATASHEETCN.COM |
ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |