X9523_06 datasheet(4/28 Pages) INTERSIL

部件名	X9523

功能描述	Laser Diode Control for Fiber Optic Modules

Download	28 Pages

Scroll/Zoom	100%

制造商	INTERSIL [Intersil Corporation]

网页	http://www.intersil.com/cda/home

标志

4 / 28 page

4

FN8209.1

January 3, 2006

PRINCIPLES OF OPERATION

SERIAL INTERFACE

Serial Interface Conventions

The device supports a bidirectional bus oriented protocol.

The protocol defines any device that sends data onto the

bus as a transmitter, and the receiving device as the

receiver. The device controlling the transfer is called the

master and the device being controlled is called the

slave. The master always initiates data transfers, and

provides the clock for both transmit and receive opera-

tions. Therefore, the X9523 operates as a slave in all

applications.

Serial Clock and Data

Data states on the SDA line can change only while SCL

is LOW. SDA state changes while SCL is HIGH are

reserved for indicating START and STOP conditions.

See Figure 1.On power-up of the X9523, the SDA pin is

in the input mode.

Serial Start Condition

All commands are preceded by the START condition,

which is a HIGH to LOW transition of SDA while SCL is

HIGH. The device continuously monitors the SDA and

SCL lines for the START condition and does not respond

to any command until this condition has been met. See

Figure 2.

Serial Stop Condition

All communications must be terminated by a STOP

condition, which is a LOW to HIGH transition of SDA

while SCL is HIGH. The STOP condition is also used to

place the device into the Standby power mode after a

read sequence. A STOP condition can only be issued

after the transmitting device has released the bus. See

Figure 2.

Serial Acknowledge

An ACKNOWLEDGE (ACK) is a software convention

used to indicate a successful data transfer. The trans-

mitting device, either master or slave, will release the

bus after transmitting eight bits. During the ninth clock

cycle, the receiver will pull the SDA line LOW to

ACKNOWLEDGE that it received the eight bits of data.

Refer to Figure 3.

The device will respond with an ACKNOWLEDGE after

recognition of a START condition if the correct Device

Identifier bits are contained in the Slave Address Byte. If

a write operation is selected, the device will respond with

an ACKNOWLEDGE after the receipt of each subse-

quent eight bit word.

In the read mode, the device will transmit eight bits of

data, release the SDA line, then monitor the line for an

ACKNOWLEDGE. If an ACKNOWLEDGE is detected

and no STOP condition is generated by the master, the

device will continue to transmit data. The device will ter-

SCL

SDA

Data Stable

Data Change

Data Stable

Figure 1.

Valid Data Changes on the SDA Bus

SCL

SDA

Start

Stop

Figure 2.

Valid Start and Stop Conditions

X9523

类似零件编号 - X9523_06

制造商	部件名	数据表	功能描述
Intersil Corporation	X9523B20I-A	509Kb / 30P	Laser Diode Control for Fiber Optic Modules
	X9523B20I-B	509Kb / 30P	Laser Diode Control for Fiber Optic Modules
	X9523V20I-A	509Kb / 30P	Laser Diode Control for Fiber Optic Modules
Renesas Technology Corp	X9523V20I-A	1Mb / 29P	Laser Diode Control for Fiber Optic Modules Dual DCP, POR, Dual Voltage Monitors
Intersil Corporation	X9523V20I-B	509Kb / 30P	Laser Diode Control for Fiber Optic Modules

More results

类似说明 - X9523_06

制造商	部件名	数据表	功能描述
Intersil Corporation	X9523	509Kb / 30P	Laser Diode Control for Fiber Optic Modules
	X9522	486Kb / 29P	Laser Diode Control for Fiber Optic Modules
	X9521	415Kb / 25P	Fiber Channel/Gigabit Ethernet Laser Diode Control for Fiber Optic Modules
	X9525	578Kb / 26P	Fiber Channel/Gigabit Etherner Laser Diode Control for Fiber Optic Modules
Renesas Technology Corp	X9522	1Mb / 29P	Laser Diode Control for Fiber Optic Modules Triple DCP, Dual Voltage Monitors
	X9521	935Kb / 24P	Dual DCP, EEPROM Memory Fiber Channel/Gigabit Ethernet Laser Diode Control for Fiber Optic Modules
	X9525	1,013Kb / 26P	Fiber Channel/Gigabit Ethernet Laser Diode Control for Fiber Optic Modules Dual DCP, EEPROM Memory
	X9523	1Mb / 29P	Laser Diode Control for Fiber Optic Modules Dual DCP, POR, Dual Voltage Monitors
	X9520	1Mb / 29P	Fiber Channel/Gigabit Ethernet Laser Diode Control for Fiber Optic Modules Triple DCP, POR, 2kbit EEPROM Memory, Dual Voltage Monitors
California Eastern Labs	NX6510GH	946Kb / 6P	LASER DIODE IN COAXIAL PACKAGE FOR FIBER OPTIC COMMUNICATIONS