数据搜索系统,热门电子元器件搜索 |
|
LA4460N 数据表(PDF) 6 Page - Sanyo Semicon Device |
|
LA4460N 数据表(HTML) 6 Page - Sanyo Semicon Device |
6 / 12 page LA4460N, 4461N No.2660–6/12 Continued from preceding page. · Soft clipping characteristics are accomplished by lowering the open loop voltage gain and reducing the amount of feedback to reduce undesired radiation to radio frequency circuits and to increase the circuit stability. The distortion deterioration resulted from the decreased amount of feedback will be avoided by using a unique distortion reduction circuit, thus 0.1% typ. will be assured. · A capacitor for oscillation compensation is included inside the IC as a method of reducing external parts. The capacitance is 30pF and this determines the cutoff frequency fH (–3dB point) of the high range (fH≈30kHz). · To reduce variations of the voltage gain, a feedback resistor RNF is also built-in, and the voltage gain is fixed to 51dB. However the voltage gain will be decreased by adding a resistor RNF’, where the RNF’ is the resistor to be connected to the pin 4. (In the Sample Application Circuit 2, the gain adjustment will be made with the resistor connected to either pin 4 or 5.) · Two ground pin terminals are provided, one for the preamplifier and the other for the power amplifier. Accordingly, stability of the IC is increased, especially, distortion deterioration phenomenon caused by increased signal source impedance Rg is improved and a flat response will be obtained. · An overvoltage protector circuit is included to protect the IC from damage when a surge voltage is applied to the power line. The overvoltage is set at 25V, however, the circuit can resist 50V for giant pulse surge of 200ms. · For OCL connections, a DC short-circuit protection circuit is required. Therefore a grounding protection circuit which endures against the OUTPUT-GND short-circuit is provided. Since consideration is given to the offset caused by short- circuit or releasing the short-circuit both the speaker and the IC can be protected. · When adding an audio muting circuit in each application circuit, refer to the illustration below. 6V ≤V M≤VCC Recommended VM=9V ATT=38dB (Rg=600 Ω) Flow-in current IO is calculated as shown below. To increase muting attenuation, connect a resistor of 5.6k Ω in series with the input circuit, then the attenuation will be increased to 55dB. It should be noted that adding an input capacitor will increase pop noise when the AC muting is operated. Pop noise can be reduced by increasing the value of R1 and C1. RNF=53Ω, Rf=20kΩ when RNF’=0 VG=20log (dB) when RNF’ is used VG=20log (dB) Rf RNF Rf RNF + RNF’ 2 IO= VM – VBE R1 |
类似零件编号 - LA4460N |
|
类似说明 - LA4460N |
|
|
链接网址 |
隐私政策 |
ALLDATASHEETCN.COM |
ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |