数据搜索系统,热门电子元器件搜索 |
|
DPX2NA-67MPAW8P33A-01 数据表(PDF) 9 Page - ITT Industries |
|
DPX2NA-67MPAW8P33A-01 数据表(HTML) 9 Page - ITT Industries |
9 / 16 page www.ittcannon.com 33. Dimensions are shown in inches (millimeters). Dimensions subject to change. MIL-C-81659 Rack and Panel Connectors DPXNA/DPXNE Coaxial Contact Data Installation Data 1. Use basic tool M22520/5-01 with Y-211 die (#995-0002-249) for crimping. 2. Use extraction tool No. CET-C8. An insertion tool is not requried (See Note 5). 3. Center contact, rear insulator, crimp ring, support bushing (not applicable to RG58/RG142 coax- ials), seal sleeve, front insulator, shell and ferrule are shipped unassembled in a common container. Without Seal Socket Pin Sealed BUSHING BUSHING BRAID FERRULE .350 (8.89) APPROX. CRIMP AREA FRONT INSULATOR COAXIAL SHELL .156 (3.96) .146 (3.71) CONTACT REAR INSULATOR .035 (0.89) .030 (0.76) Push ferrule under braid as far as it will go. Trim off braid extending beyond shoulder of ferrule, if necessary. While holding ferrule in place pull crimp sleeve forward over braid untill it is tight against shoulder on ferrrule. Pull firmly against face of ferrule to make sure it is up tight. Trim dielectric to the .035 (0.89)/.030 (0.76) dimension. Place front insulator over contact and then push assembly into coaxial shell. Place parts in jaw of crimp tool. Locate jaws at start of chamber on crimp sleeve. Press sleeve firmly into coaxial shell and crimp. After assembled coaxial is inserted into connector, push suppurt bushing into grommet until shoulder rests on tubular extension. Then pull sealing sleeve forward until it is snug on grommet. A. B. C. A. B. C. Carefully push inner conductor through rear insulator. While holding rear insulator firmly against ferrule, trim conductor to .156 (3.96)/.146 (3.91) dimension. Place contact over conductor and solder. A. B. C. SEAL 2 SEAL 1 SEAL 4. Cable Assembly Instructions Step 1 - If applicable determine which portion of seal sleeve should be used. If Seal 2 is used, cut off Seal 1 portion. Step 2 - In sequence, place seal sleeve, support bushing and crimp ring over cable jacket. Step 3 - Trim cable per illustration. Step 4 - Comb out braid and flare out ends to permit entry of ferrule. Step 5 - Complete termination per illustration. 5. To extract coaxial, push back seal sleeve and support bushing. Slip cable into extraction tool Push tool into insert until contacts coaxial retain- ing shoulder. Grip both cable and tool with one hand and pull coaxial rearward out of insert cavity. 6. To facilitate extraction of contacts, the length of free cable adjacent to the rear surface of the connector should not be less than 2.000 (50.80). |
类似零件编号 - DPX2NA-67MPAW8P33A-01 |
|
类似说明 - DPX2NA-67MPAW8P33A-01 |
|
|
链接网址 |
隐私政策 |
ALLDATASHEETCN.COM |
ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |