UNIVERSAL AC INPUT HARMONIC CORRECTION AC-DC HOT-SWAP

CompactPCI QUAD OUTPUT 200 WATTS ACTIVE CURRENT SHARING

SWITCHING POWER SUPPLIES TPAC200P SERIES

GENERAL SPECIFICATION

Efficiency: Typ. 76-79 %.

Switching Frequency: 130K Hz.

Circuit Topology: Forward circuit.

Transient Response: Peak transient less than 100mV and

recovers within 3mS after 25% load-change.

Safety Standard: IEC60950 Class I.

Construction: Eurocard 3U X 8HP X 160mm

CompactPCI format. Front Panel with

either Ordinary handle or Extractor handle.

Operating Temperature: 0 to +50 °C at full load with

specified air flow. Derates linearly to 50% at +70°C.

Storage Temperature: -40 to +85 °C.

Temperature Coefficient: Typ. ±0.02% / °C.

Cooling: At least 20cfm (600 lfm) moving air

is required to achieve full rating power 200W

in a confined area.

Power Density: 3.73 Watts/ Cubic Inch.

Remark: All measurements are at nominal input, full load and +25°C unless otherwise specifications.

FEATURES:

200W 3U X 8HP EUROCARD PACKAGE

MEET IEC1000-3-2 HARMONIC CORRECTION

INTERNAL OR-ING DIODES FOR

N+1 REDUNDANCY

HOT-SWAPPABLE

THIRD-WIRE CURRENT SHARING

EMI MEET EN 55022 / FCC CLASS A

CE MARKING COMPLIANCE

FULLY COMPLIANT WITH PICMG

SPECIFICATION

INPUT SPECIFICATION

Input Voltage: Typ. 90-264Vac.

Power Factor Correction: Meet Harmonic Correction

IEC1000-3-2.Power Factor typ. 0.96-0.98.

Input Connector: Positronic 47-pin PCIH47M400A1.

Input Frequency: 47-63Hz.

Inrush Current: Less than 30.6A @ 230Vac.

Input Current: 2.3A @115Vac/1.2A @230Vac.

Dielectric Withstand: Meet IEC950 regulation.

EMI: Meet EN55022 / FCC Class A.

Hold-up Time: 10mS after power fail signal.

Turn-on Delay/Rise Time: 1 Sec./20 mS.

Earth Leakage: Less than 0.5mA @230Vac.

Remote ON/OFF: Available at [INH#] & [EN#] pins.

Power Fail Signal: Available at [FAL#] pin.

Status LED: <Green> means valid input voltage.

<Amber> means a critical fault.

Thermal Protection (OTP): Installed NTC and thermostat.

for thermal sensor at [DEG#] pin.

Leakage Current: Typ. 0.5A.

Power OK Signal: Available at all output.

Over Current Protection (OCP): Installed in each rail.

OUTPUT SPECIFICATION

Output Voltage: See Ratings Chart.

Output Current: See Ratings Chart.

Output Wattage: Typ. 200W continuous.

Output Connector: Positronic 47-PIN

PCIH47M400A1 connector.

Line Regulation: Typ. 0.1%.

Load Regulation: VO1 & VO2 typ. ±1.0%.

VO3 & VO4 typ. ±2.0%.

Noise & Ripple: Typ. 1% peak to peak or 50mV,

which is greater.

OVP: Built-in at all outputs.

Adjustability: Available at VO1,2&3.

Output Trim: Electrical trim available at VO1&2. [ADJ #].

Remote Sensing: Available at VO1,VO2 & VO3.

Hot-Swap: Available.

N+1 Redundancy: Installed with internal OR-ing diodes at

all outputs for N+1 redundancy operation.

Current Sharing: Third-wire current sharing at VO1,2 & 3.

Overload Protection (OLP): Fully protected against output

overload or short circuit. Typ. set at 130% max. load.

Consult the factory for special OLP setting.

In application

TOTAL POWER INT'L

TOTAL POWER, INT. Tel: 877-646-0900 Fax: 978-453-7395

Email: sales@total-power.com http://www.total-power.com

-1-