数据搜索系统,热门电子元器件搜索 |
|
DAC8812IBPW 数据表(PDF) 11 Page - Texas Instruments |
|
|
DAC8812IBPW 数据表(HTML) 11 Page - Texas Instruments |
11 / 18 page www.ti.com THEORY OF OPERATION CIRCUIT OPERATION Digital-to-Analog Converters R R R 2R 2R 2R R 5 kW S2 S1 DGND V X REF V DD R X FB I X OUT A X GND Digital interface connections omitted for clarity. Switches S1 and S2 are closed, V must be powered. DD V OUT + *VREF D 65536 (1) DAC8812 SBAS349A – AUGUST 2005 – REVISED DECEMBER 2005 The DAC8812 contains two 16-bit, current-output, digital-to-analog converters (DACs). Each DAC has its own independent multiplying reference input. The DAC8812 uses a 3-wire, SPI-compatible serial data interface, with a configurable asynchronous RS pin for half-scale (MSB = 1) or zero-scale (MSB = 0) preset. In addition, an LDAC strobe enables two channel simultaneous updates for hardware synchronized output voltage changes. The DAC8812 contains two current-steering R-2R ladder DACs. Figure 30 shows a typical equivalent DAC. Each DAC contains a matching feedback resistor for use with an external I-to-V converter amplifier. The RFBX pin is connected to the output of the external amplifier. The IOUTX terminal is connected to the inverting input of the external amplifier. The AGNDX pin should be Kelvin-connected to the load point in the circuit requiring the full 16-bit accuracy. Figure 30. Typical Equivalent DAC Channel The DAC is designed to operate with both negative or positive reference voltages. The VDD power pin is only used by the logic to drive the DAC switches on and off. Note that a matching switch is used in series with the internal 5 k Ω feedback resistor. If users are attempting to measure the value of R FB, power must be applied to VDD in order to achieve continuity. The DAC output voltage is determined by VREF and the digital data (D) according to Equation 1: Note that the output polarity is opposite of the VREF polarity for dc reference voltages. The DAC is also designed to accommodate ac reference input signals. The DAC8812 accommodates input reference voltages in the range of –15 V to +15 V. The reference voltage inputs exhibit a constant nominal input resistance of 5 k Ω, ±20%. On the other hand, DAC outputs I OUTA and B are code-dependent and produce various output resistances and capacitances. The choice of external amplifier should take into account the variation in impedance generated by the DAC8812 on the amplifiers' inverting input node. The feedback resistance, in parallel with the DAC ladder resistance, dominates output voltage noise. For multiplying mode applications, an external feedback compensation capacitor (CFB) may be needed to provide a critically damped output response for step changes in reference input voltages. 11 |
类似零件编号 - DAC8812IBPW |
|
类似说明 - DAC8812IBPW |
|
|
链接网址 |
隐私政策 |
ALLDATASHEETCN.COM |
ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |