数据搜索系统,热门电子元器件搜索 |
|
BM63374S-VA 数据表(PDF) 7 Page - Rohm |
|
BM63374S-VA 数据表(HTML) 7 Page - Rohm |
7 / 24 page 7/21 BM63374S-VA BM63374S-VC TSQ50501-BM63374S-2 © 2020 ROHM Co., Ltd. All rights reserved. 30.Jul.2020 Rev.001 www.rohm.com TSZ22111・15・001 Mechanical Characteristics And Ratings Item Limit Unit Following Standard Conditions Min Typ Max Mounting Torque 0.59 0.69 0.78 N・m - Mounting Screw M3 (Note 1) Recommended 0.69N・m (Note 2) Pin Pulling Strength 10 - - s EIAJ-ED-4701/400 Load Control Pin:4.9N Power Pin:9.8N Pin Bending Strength 2 - - times EIAJ-ED-4701/400 Load Control Pin: 2.45N Power Pin:4.9N 90deg. Bend Weight - 10 - g - Heat Sink Flatness 0 - +200 µm - Measurement point is provided in Figure 6-1. (Note 1) Plain washers of 8mm outside diameter (ISO 7089 to 7094) are recommended. (Note 2) When installing a module to a heat sink, excessive uneven fastening force might apply stress to inside chips or ceramic of heat sink plate, which will break or crack or degrade a module. An example of recommended fastening sequence is shown in Figure 5. The temporary fastening torque is set to 20 to 30% of the maximum torque rating. Evenly apply thermally-conductive grease with 100µm to 200µm thickness over the contact surface between the module and the heat sink. Also, pay attention not to have any dirt left on the contact surface between the module and the heat sink. It is recommended to install a module directly to a heat sink after applying grease. When installing a module to a heat sink, inserting a heat radiation sheet between a module and a heat sink might apply stress depending on thickness and elastic modulus of the sheet to inside chips or ceramic of heat sink plate, which will break or crack or degrade a module. When using a heat radiation sheet, it is needed to prevent IPM from bending into + side of Figure 6-2. Figure 5. Example of Recommended Fastening Sequence (+) (+) TOP VIEW 2 1 Temporary fastening:1→2 Permanent fastening:1→2 Figure 6-1. Measurement Point of Heat Sink Flatness (+) Heatsink Heat Radiation Sheet Figure 6-2. Flatness after Installing to a Heat Sink (When Using a Heat Radiation Sheet) |
类似零件编号 - BM63374S-VA |
|
类似说明 - BM63374S-VA |
|
|
链接网址 |
隐私政策 |
ALLDATASHEETCN.COM |
ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |