数据搜索系统,热门电子元器件搜索 |
|
SN74LS221 数据表(PDF) 3 Page - ON Semiconductor |
|
SN74LS221 数据表(HTML) 3 Page - ON Semiconductor |
3 / 8 page SN74LS221 http://onsemi.com 3 OPERATIONAL NOTES Once in the pulse trigger mode, the output pulse width is determined by tW = RextCextIn2, as long as Rext and Cext are within their minimum and maximum valves and the duty cycle is less than 50%. This pulse width is essentially independent of VCC and temperature variations. Output pulse widths varies typically no more than ±0.5% from device to device. If the duty cycle, defined as being 100 @ tW T where T is the period of the input pulse, rises above 50%, the output pulse width will become shorter. If the duty cycle varies between low and high valves, this causes the output pulse width to vary in length, or jitter. To reduce jitter to a minimum, Rext should be as large as possible. (Jitter is independent of Cext). With Rext = 100K, jitter is not appreciable until the duty cycle approaches 90%. Although the LS221 is pin-for-pin compatible with the LS123, it should be remembered that they are not functionally identical. The LS123 is retriggerable so that the output is dependent upon the input transitions once it is high. This is not the case for the LS221. Also note that it is recommended to externally ground the LS123 Cext pin. However, this cannot be done on the LS221. The SN74LS221 is a dual, monolithic, non-retriggerable, high-stability one shot. The output pulse width, tW can be varied over 9 decades of timing by proper selection of the external timing components, Rext and Cext. Pulse triggering occurs at a voltage level and is, therefore, independent of the input slew rate. Although all three inputs have this Schmitt-trigger effect, only the B input should be used for very long transition triggers ( ≥1.0 µV/s). High immunity to VCC noise (typically 1.5 V) is achieved by internal latching circuitry. However, standard VCC bypassing is strongly recommended. The LS221 has four basic modes of operation. Clear Mode: If the clear input is held low, irregardless of the previous output state and other input states, the Q output is low. Inhib- it Mode: If either the A input is high or the B input is low, once the Q output goes low, it cannot be retriggered by other inputs. Pulse Trigger Mode: A transition of the A or B inputs as indicated in the functional truth table will trigger the Q output to go high for a duration determined by the tW equation described above; Q will go low for a corresponding length of time. The Clear input may also be used to trigger an output pulse, but special logic precondi- tioning on the A or B inputs must be done as follows: Following any output triggering action using the A or B inputs, the A input must be set high OR the B input must be set low to allow Clear to be used as a trigger. Inputs should then be set up per the truth table (without triggering the output) to allow Clear to be used a trigger for the output pulse. If the Clear pin is routinely being used to trigger the output pulse, the A or B inputs must be toggled as described above before and between each Clear trigger event. Once triggered, as long as the output remains high, all input transitions (except overriding Clear) are ignored. Overriding Clear Mode: If the Q output is high, it may be forced low by bringing the clear input low. |
类似零件编号 - SN74LS221 |
|
类似说明 - SN74LS221 |
|
|
链接网址 |
隐私政策 |
ALLDATASHEETCN.COM |
ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |