 |
数据搜索系统，热门电子元器件搜索 |
|
|
数据搜索系统，热门电子元器件搜索 |
|
JS28F320J3A-115 数据表(PDF) 46 Page - Intel Corporation |
|
||||||||||||||||||||||||||||||
JS28F320J3A-115 数据表(HTML) 46 Page - Intel Corporation |
|
|
46 / 72 page  256-Mbit J3 (x8/x16) 46 Datasheet 13.0 Security Modes This device offers both hardware and software security features. Block lock operations, PRs, and VPEN allow the user to implement various levels of data protection. The following section describes security features in detail. Other security features are available that are not described in this datasheet. Please contact your local Intel Field Representative for more information. 13.1 Set Block Lock-Bit A flexible block locking scheme is enabled via block lock-bits. The block lock-bits gate program and erase operations. Individual block lock-bits can be set using the Set Block Lock-Bit command. This command is invalid while the WSM is running or the device is suspended. Set block lock-bit commands are executed by a two-cycle sequence. The set block setup along with appropriate block address is followed by either the set block lock-bit confirm (and an address within the block to be locked). The WSM then controls the set lock-bit algorithm. After the sequence is written, the device automatically outputs Status Register data when read (see Figure 24 on page 65). The CPU can detect the completion of the set lock-bit event by analyzing the STS signal output or SR.7. When the set lock-bit operation is complete, SR.4 should be checked. If an error is detected, the Status Register should be cleared. The CUI will remain in Read Status Register mode until a new command is issued. This two-step sequence of setup followed by execution ensures that lock-bits are not accidentally set. An invalid Set Block Lock-Bit command will result in SR.4 and SR.5 being set. Also, reliable operations occur only when VCC and VPEN are valid. With VPEN ≤ VPENLK, lock-bit contents are protected against alteration. 13.2 Clear Block Lock-Bits All set block lock-bits are cleared in parallel via the Clear Block Lock-Bits command. Block lock- bits can be cleared using only the Clear Block Lock-Bits command. This command is invalid while the WSM is running or the device is suspended. Clear block lock-bits command is executed by a two-cycle sequence. A clear block lock-bits setup is first written. The device automatically outputs Status Register data when read (see Figure 25 on page 66). The CPU can detect completion of the clear block lock-bits event by analyzing the STS signal output or SR.7. When the operation is complete, SR.5 should be checked. If a clear block lock-bit error is detected, the Status Register should be cleared. The CUI will remain in Read Status Register mode until another command is issued. |
类似零件编号 - JS28F320J3A-115 |
|
类似说明 - JS28F320J3A-115 |
|
|
链接网址 |
| 隐私政策 |
| ALLDATASHEETCN.COM |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Chinese ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
