数据搜索系统,热门电子元器件搜索 |
|
TSB41AB3-EP 数据表(PDF) 9 Page - Texas Instruments |
|
|
TSB41AB3-EP 数据表(HTML) 9 Page - Texas Instruments |
9 / 52 page TSB41AB3EP IEEE 1394a2000 THREEPORT CABLE TRANSCEIVER/ARBITER SGLS122B − JULY 2002 − REVISED DECEMBER 2004 9 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 Terminal Functions (Continued) TERMINAL I/O DESCRIPTION NAME TYPE NO. I/O DESCRIPTION SM CMOS 33 I Test control input. This input is used in the manufacturing test of the TSB41AB3. For normal use this terminal is tied to GND. SYSCLK CMOS 2 O System clock output. Provides a 49.152-MHz clock signal, synchronized with data transfers, to the LLC. TESTM CMOS 31 I Test control input. This input is used in the manufacturing test of the TSB41AB3. For normal use this terminal is tied to VDD through a 1-kΩ resistor. TPA0+ TPA1+ TPA2+ Cable 45 52 58 I/O Twisted-pair cable A differential-signal terminals. Board traces from each pair of positive and negative differential signal terminals must be kept matched and as short as possible to the TPA0− TPA1− TPA2− Cable 44 51 57 I/O negative differential signal terminals must be kept matched and as short as possible to the external load resistors and to the cable connector. For an unused port, TPA+ and TPA− can be left open. TPB0+ TPB1+ TPB2+ Cable 43 50 56 I/O Twisted-pair cable B differential-signal terminals. Board traces from each pair of positive and negative differential signal terminals should be kept matched and as short as possible to the external load resistors and to the cable connector. For each unused port, TPB+ and TPB− TPB0− TPB1− TPB2− Cable 42 49 55 I/O external load resistors and to the cable connector. For each unused port, TPB+ and TPB− terminals can be tied together and then connected to ground through a 1-k Ω resistor or the TPB+ and TPB− terminals can be connected to the suggested termination network. TPBIAS0 TPBIAS1 TPBIAS2 Cable 46 53 59 I/O Twisted-pair bias output. This provides the 1.86-V nominal bias voltage needed for proper operation of the twisted-pair cable drivers and receivers and for signaling to the remote nodes that there is an active cable connection. Each of these terminals, except for an unused port, must be decoupled with a 1.0- µF capacitor to ground. For the unused port, this terminal can be left unconnected. VDD-5V Supply 9 − 5-V VDD terminal. This terminal must be connected to the LLC VDD supply when a 5-V LLC is used, and connected to the PHY DVDD when a 3-V LLC is used. A combination of high-frequency decoupling capacitors near this terminal is suggested, such as paralleled 0.1 µF and 0.001 µF. When this terminal is tied to a 5-V supply, all terminal bus holders are disabled, regardless of the state of the ISO terminal. When this terminal is tied to a 3-V supply, bus holders are enabled when the ISO terminal is high. XI XO Crystal 76 77 − Crystal oscillator inputs. These terminals connect to a 24.576-MHz parallel resonant fundamental mode crystal. The optimum values for the external shunt capacitors are dependent on the specifications of the crystal used (see crystal selection in the Applications Information section). When an external clock source is used, XI should be the input and XO should be left open, and the clock must be supplied before the device is taken out of reset. NOTE: It is strongly recommended that signals tied to VDD use a 1-kΩ resistor (minimum). Tying signals directly to VCC may result in ESD failures. Signals tied to ground may be tied directly. |
类似零件编号 - TSB41AB3-EP |
|
类似说明 - TSB41AB3-EP |
|
|
链接网址 |
隐私政策 |
ALLDATASHEETCN.COM |
ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |